Maytag MGS8880DS Instruccion De Instalación

1. Slide range into final location, making sure rear leveling leg 

slides into anti-tip bracket.

2. Remove the premium storage drawer. See the “Remove/

Replace Drawer” section.

3. Use a flashlight to look underneath the bottom of the range.

4. Visually check that the rear range foot is inserted into the slot 

of the anti-tip bracket.

1. Slide range into final location, making sure rear leveling leg 

slides into anti-tip bracket. Leave a 1" (2.5 cm) gap between 
the back of the range and the back wall.

2. Place the outside of your foot against the bottom front of the 

warming drawer or baking drawer to keep the range from 
moving, and then grasp the back of the range, as shown.

3. Slowly attempt to tilt the range forward. 

If you encounter immediate resistance, the range foot is 
engaged in the anti-tip bracket. Go to Step 8.

4. If the rear of the range lifts more than ½" (1.3 cm) off the floor 

without resistance, stop tilting the range and lower it gently 
back to the floor. The range foot is not engaged in the anti-tip 
bracket.

IMPORTANT: If there is a snapping or popping sound when 
lifting the range, the range may not be fully engaged in the 
bracket. Check to see if there are obstructions keeping the 
range from sliding to the wall or keeping the range foot from 
sliding into the bracket. Verify that the bracket is held 
securely in place by the mounting screws.

5. Slide the range forward, and verify that the anti-tip bracket is 

securely attached to the floor or wall.

6. Slide range back so the rear range foot is inserted into the 

slot of the anti-tip bracket.

7. Repeat steps 1 and 2 to ensure that the range foot is 

engaged in the anti-tip bracket.

If the rear of the range lifts more than ½" (1.3 cm) off the floor 
without resistance, the anti-tip bracket may not be installed 
correctly. Do not operate the range without anti-tip bracket 
installed and engaged. Please reference the “Warranty” 
section of the User Guide to contact service.

8. Move the range into its final location. Check that the range is 

level by placing a level on the oven bottom. See the “Level 
Range” section.

IMPORTANT: If the range is moved to adjust the leveling 
legs, verify that the anti-tip bracket is engaged by repeating 
steps 1 to 8.

Cooktop and oven burners use electronic igniters in place of 
standing pilots. When the cooktop control knob is turned to the 
ignite position, the system creates a spark to light the burner. All 
cooktop burners will spark, but only the burner with the control 
knob turned to the ignite position will produce a flame. This 
sparking continues as long as the control knob is turned to the 
ignite position.

When the oven control is turned to the desired setting, sparking 
occurs and ignites the gas.

Push in and turn each control knob to the ignite position. 

The flame should light within 4 seconds. The first time a burner is 
lit, it may take longer than 4 seconds to light because of air in the 
gas line. 

■

Turn cooktop control knob to the off position. 

■

Check that the range is plugged into a grounded 3 prong 
outlet. Check that the circuit breaker has not tripped or the 
household fuse has not blown. 

■

Check that the gas shutoff valves are set to the open 
position. 

■

Check that burner caps are properly positioned on burner 
bases.

Repeat start-up. If a burner does not light at this point, turn the 
control knobs to the off position and contact your dealer or 
authorized service company for assistance. Please reference the 
“Warranty” section of the User Guide to contact service

If the cooktop “low” burner flame needs to be adjusted for any of 
the burners, see the “Adjust Flame Height” section.

1. Press BAKE.

2. Press the Start pad.

The oven burner should light within 8 seconds. The first time 
a burner is lit, it may take longer than 8 seconds to light 
because of air in the gas line.

3. After 2 minutes, open the oven door and check that the oven 

is warm.

■

Press the Off pad.

■

Check that the range is plugged into a grounded 3 prong 
outlet. Check that the circuit breaker has not tripped or the 
household fuse has not blown. 

■

Check that the gas shutoff valves are set to the open 
position.