Amana AE183G35AX Uso Y Cuidado

16

How to set:
Press the 

TIMER 0.5-24 hr pad on the unit or the

TIMER 

pad

on the remote control. Each touch of the 

/ DECREASE   pads on the unit or the INCREASE (+) /

DECREASE (-) pads on the remote control will set the

timer in 0.5 (1/2 hr.) or 1-hour intervals. (The delay timer

can be set in 0.5 (1/2 hr.) increments if programmed for

under 10 hours, but if the delay timer is set for above 10

hours, the timer will be set in 1-hour increments.)  The

SET light will turn on while setting.
To review the remaining time ,

press the 

TIMER  0.5-24 hr pad on the unit or the TIMER pad

on the remote control. Use the 

CREASE  pads on the unit or the INCREASE (+) /

DECREASE (-) pads on the remote control to set a new

time if desired.
To cancel the timer, press and hold the 

 

u

Turn on to provide continuous side-to-side air circulation.

For fixed side-to-side air direction, turn on until the de-

sired air direction is obtained, then turn it off.

•

To ensure proper operation, aim the remote control at

the signal receiver on the air conditioner.

•

The remote control signal has a range of up to 20 feet.

•

Make sure nothing is between the air conditioner and

the remote control that could block the signal.

•

Make sure your batteries are fresh and installed cor-

rectly as indicated on the remote control.

Use the 

COOL mode at LOW, MED, HIGH, or AUTO

FAN SPEED for cooling.  Use the TEMPERATURE IN-

/ DECREASE  pads to set the desired

temperature between 61° and 86°F in 1° increments.
The compressor will cycle on and off to keep the room at

the set level of comfort. Set the thermostat at a lower

number and the indoor air will become cooler. Set the

thermostat at a higher number and the indoor air will be-

come warmer.
NOTE: If the air conditioner is off and then turned on

while set to a 

COOL setting, or if it is turned from a fan

setting to a 

COOL setting, it may take approximately 3

minutes for the compressor to start and cooling to begin.

Select the 

COOL mode and HIGH

or 

MED fan with a middle set temperature.

Select the 

COOL mode and

HIGH fan with a lower set temperature.
For  Quieter & Nighttime Cooling - 

Select the 

mode and 

LOW fan with a middle set temperature.

Controls the fan.
ON - 

The fan will cycle on and off with the compressor.

This results in wider variations of room temperature
and humidity and is normally used when the room is
unoccupied.
NOTE: The fan may continue to run for a short time after

the compressor cycles off.

The fan runs all the time, while the compressor

cycles on and off.

Use the 

FAN ONLY mode at LOW, MED or HIGH fan

speed to provide air circulation and filtering without cool-

ing.  Since the fan only settings do not provide cooling, a

SET temperature cannot be entered. The room tempera-

ture will appear in the display.
NOTE: Auto Fan Speed cannot be used when in the FAN

ONLY mode.

Use the 

HEAT mode at LOW, MED, HIGH or AUTO FAN

SPEED for heating.  Use the TEMPERATURE INCREASE

pads to set the desired tempera-

ture between 61°F and 86°F in 1°F increments.

Set to 

AUTO fan speed for the fan speed to automati-

cally set to the speed needed to provide optimum com-

fort settings with the set temperature. If the room needs

more cooling, the fan speed will automatically increase.

If the room needs less cooling, the fan speed will auto-

matically decrease.
NOTE: Auto Fan Speed cannot be used when in the FAN

ONLY mode.

In the case of a power outage or interruption, the unit will

automatically re-start in the settings last used, after the

power is restored.  If the 

TIMER 0.5-24 hr feature was set,

it will resume countdown.  You may need to set a new

time if desired.