Thermador PRG304GH Folleto
1.800.735.4328 | THERMADOR.COM
59
PRO HARMONY RANGES
PRO HARMONY
®
RANGES
48-INCH GAS
PRG486GDH / PRL486GDH
INSTALLATION OPTIONS
Thermador Pro Harmony
®
Ranges feature a
bold, professional design and a compact,
24-inch depth profile that creates a seamless
look within standard cabinetry. These ranges
can be installed in a wall or island installation.
24-inch depth profile that creates a seamless
look within standard cabinetry. These ranges
can be installed in a wall or island installation.
BACKGUARDS
When using the Flush Island Trim, Thermador
recommends a minimum 12" (305 mm) rear
clearance to a combustible surface (see Figure
1, Cabinet Clearances). Clearances from non-
combustible materials are not part of the ANSI
Z21.1 scope and are not certified by CSA.
Clearances of less than 12" (305 mm) must be
approved by the local codes and / or by the
local authority having jurisdiction.
recommends a minimum 12" (305 mm) rear
clearance to a combustible surface (see Figure
1, Cabinet Clearances). Clearances from non-
combustible materials are not part of the ANSI
Z21.1 scope and are not certified by CSA.
Clearances of less than 12" (305 mm) must be
approved by the local codes and / or by the
local authority having jurisdiction.
NATURAL GAS OR LP
Thermador All-Gas Pro harmony Ranges are
shipped by the factory to operate on natural
gas or LP. Be sure to order the correct fuel-
type and verify the type of gas being used at
the installation site matches the type of gas
used by the appliance.
shipped by the factory to operate on natural
gas or LP. Be sure to order the correct fuel-
type and verify the type of gas being used at
the installation site matches the type of gas
used by the appliance.
IMPORTANT
We strongly recommend that a Thermador
Professional Wall or Island Hood or Custom
Insert be installed with all Thermador Pro
Harmony Ranges. Downdraft ventilation should
not be used. Do not install a microwave-hood
combination above the cooktop, as these
types of units do not provide the proper
ventilation and are not suitable for use with
Thermador Pro Harmony Ranges. Refer to the
Ventilation section or www.Thermador.com for
a complete selection of Professional ventilation
options, blowers, and accessories.
Professional Wall or Island Hood or Custom
Insert be installed with all Thermador Pro
Harmony Ranges. Downdraft ventilation should
not be used. Do not install a microwave-hood
combination above the cooktop, as these
types of units do not provide the proper
ventilation and are not suitable for use with
Thermador Pro Harmony Ranges. Refer to the
Ventilation section or www.Thermador.com for
a complete selection of Professional ventilation
options, blowers, and accessories.
Due to the high surface temperature
output of the Pro Harmony Ranges, the
HPWB Professional Series Wall Hoods or
the Professional Series Custom Inserts are
recommended ventilation solutions for these
ranges. The PH Professional Series Wall
Hoods are also a viable option.
output of the Pro Harmony Ranges, the
HPWB Professional Series Wall Hoods or
the Professional Series Custom Inserts are
recommended ventilation solutions for these
ranges. The PH Professional Series Wall
Hoods are also a viable option.
48-INCH CUTOUT AND RANGE DIMENSIONS
NOTE: A 36-inch minimum clearance is required between the top of the
cooking surface and the bottom of an unprotected cabinet. A 30-inch
clearance can be used when the bottom of the wood or metal cabinet is
protected by not less than
cooking surface and the bottom of an unprotected cabinet. A 30-inch
clearance can be used when the bottom of the wood or metal cabinet is
protected by not less than
1
/
4
inch of a flame retardant material covered with
not less than No. 28 MSG sheet steel, 0.015 inch (0.4 mm) thick stainless
steel, 0.024 inch (0.6 mm) aluminum, or 0.020 inch (0.5 mm) thick copper.
steel, 0.024 inch (0.6 mm) aluminum, or 0.020 inch (0.5 mm) thick copper.
as defined in the “National Fuel Gas Code” (ANSI Z223.1,
Current Edition). Clearances from non-combustible materials
are not part of the ANSI Z21.1 scope and are not certified by
CSA. Clearances of less than 12” (305 mm) must be approved
by the local codes and/or by the local authority having
jurisdiction.
as defined in the “National Fuel Gas Code” (ANSI Z223.1,
Current Edition). Clearances from non-combustible materials
are not part of the ANSI Z21.1 scope and are not certified by
CSA. Clearances of less than 12” (305 mm) must be approved
by the local codes and/or by the local authority having
jurisdiction.