Thermador PRG366JG Instruccion De Instalación
English 21
When installing against a combustible surface, a High Shelf
or Low Backguard is required. A THERMADOR
or Low Backguard is required. A THERMADOR
®
High
Shelf or Low Backguard must be purchased separately.
See clearances on page 6 for more information.
See clearances on page 6 for more information.
When using the Flush Island Trim, THERMADOR
recommends a minimum 12” (305 mm) rear clearance to a
combustible surface (see Figure 1, Cabinet Clearances).
Clearances from non-combustible materials are not part of
the ANSI Z21.1 scope and are not certified by
CSA. Clearances of less than 12” (305 mm) must be
approved by the local codes and/or by the local authority
having jurisdiction.
recommends a minimum 12” (305 mm) rear clearance to a
combustible surface (see Figure 1, Cabinet Clearances).
Clearances from non-combustible materials are not part of
the ANSI Z21.1 scope and are not certified by
CSA. Clearances of less than 12” (305 mm) must be
approved by the local codes and/or by the local authority
having jurisdiction.
High Shelf Assembly
1.
Remove protective plastic.
2.
Slide the shelf onto the backguard channel.
3.
Install the included (5) stainless screws along the
topside of shelf and (8) stainless screws into the back
of the shelf.
topside of shelf and (8) stainless screws into the back
of the shelf.
4.
Begin with Backguard Installation.
Backguard Installation
1.
Remove protective plastic.
2.
Depending on model, remove the (3) or (5) T-20 Torx
stainless screws in the front face of the included Flush
Island Trim, the (4) drill point screws securing the trim
to the side panels, and the (2) or (4) drill point screws
securing the piece to the back panel. Lift up to fully
remove.
stainless screws in the front face of the included Flush
Island Trim, the (4) drill point screws securing the trim
to the side panels, and the (2) or (4) drill point screws
securing the piece to the back panel. Lift up to fully
remove.
3.
Align the back panel of the new accessory with the
flanges on the range side panels right and left rear
corners. The backguard is inserted inside the guide
channels on the back of the range.
flanges on the range side panels right and left rear
corners. The backguard is inserted inside the guide
channels on the back of the range.
4.
Make sure the backguard’s front face is outside the
flange on the front side of the range.
flange on the front side of the range.
5.
Re-install screws in the new backguard’s front and
back panels.
back panels.
6.
Re-install (4) drill point screws to secure the
backguard’s back panel to the side panels on the back
of the range.
backguard’s back panel to the side panels on the back
of the range.
Backguard Kit Model Numbers
Model
36”
48”
Low Back
PA36JLBG
PA48JLBG
High Shelf
PA36JHSG
PA48JHSG
Flush Island
Trim
Trim
Included on
Range
Range
Included on
Range
Range
F
IGURE
20: B
ACKGUARD
R
EAR
V
IEW
(12x) screws along the back
(5x) screws along the top
F
IGURE
21: B
ACKGUARD
I
NSTALLATION
High Shelf
Low Back
Flush Island Trim
(Included with range)
Mounts inside back panel flange
Mo
u
n
ts
in
si
d
e
si
d
e
p
a
n
e
l
fl
a
n
g
e
Mo
u
u
n
ts
in
si
d
e
si
d
e
p
a
n
e
l f
la
n
g
e