Maytag MFW2055DRM Hoja De Datos
10
Handle Installation
Parts Included: Handles (3)
Install Door Handles
1. Remove the handles from the packaging inside the
refrigerator.
NOTE: To avoid damaging the handles, place them on a
towel or other soft surface.
towel or other soft surface.
2. Place the keyhole slots in the handle over the shoulder
screws (preinstalled on the door). Apply firm pressure on the
handle to slide it down onto the shoulder screws.
handle to slide it down onto the shoulder screws.
NOTE: Do not push the handle toward the door; this can
damage the door. Apply only downward pressure.
damage the door. Apply only downward pressure.
3. Repeat the previous steps to install the adjacent door handle.
Install Drawer Handle
1. Place the keyhole slots in the handle over the shoulder
screws (preinstalled on the drawer). Slide the handle firmly to
the right to fully engage the shoulder screws in the keyhole
slots.
the right to fully engage the shoulder screws in the keyhole
slots.
NOTE: Do not push the handle toward the drawer; this can
damage the drawer.
damage the drawer.
2. Save all instructions.
Remove the Handles
Refrigerator Door
■
Lift the handle directly upward, and pull it off of the door.
■
If necessary, use a Phillips screwdriver to remove the
shoulder screws from the door.
shoulder screws from the door.
Freezer Drawer
■
Slide the handle to the left to disengage the keyhole slot from
the shoulder screws, and pull it off of the drawer.
the shoulder screws, and pull it off of the drawer.
■
If necessary, use a Phillips screwdriver to remove the
shoulder screws from the drawer.
shoulder screws from the drawer.
Door Closing and Door Alignment
IMPORTANT: To comply with American Disabilities Act (ADA)
guidelines, fully retract the rollers into the cabinet to lower the
refrigerator.
guidelines, fully retract the rollers into the cabinet to lower the
refrigerator.
Door Closing
The base grille covers the leveling screws and roller assemblies
located at the bottom of the refrigerator cabinet below the freezer
drawer. Before making adjustments, remove the base grille and
move the refrigerator to its final location.
located at the bottom of the refrigerator cabinet below the freezer
drawer. Before making adjustments, remove the base grille and
move the refrigerator to its final location.
1. Remove the base grille. Grasp the grille firmly and pull it
toward you.
2. Move the refrigerator to its final location.
NOTE: To allow the refrigerator to roll easier, raise the leveling
legs off the floor by turning the leveling screws
counterclockwise. The front rollers will be touching the floor.
legs off the floor by turning the leveling screws
counterclockwise. The front rollers will be touching the floor.
3. So the doors will close easier, use a
¹⁄₄" hex driver to turn both
leveling screws clockwise. This will raise the front of the
refrigerator tilting it slightly downward to the rear. Turn both
leveling screws the same amount.
refrigerator tilting it slightly downward to the rear. Turn both
leveling screws the same amount.
NOTE: Having someone push against the top of the
refrigerator takes some weight off the leveling screws. This
makes it easier to turn the screws.
refrigerator takes some weight off the leveling screws. This
makes it easier to turn the screws.
4. Open both doors again to make sure they close as easily as
you like and that they stay closed. If not, tilt the refrigerator
slightly more to the rear by turning both leveling screws to the
right. It may take several more turns.
slightly more to the rear by turning both leveling screws to the
right. It may take several more turns.
NOTE: To keep the refrigerator level, you should turn both
leveling screws the same amount.
leveling screws the same amount.
A. Leveling screw
B. Front roller
B. Front roller
A
¹⁄₄
"
B