Bose® Wave SoundTouch Manual De Propietario

Maintaining Your Wave® SoundTouch™ Music System

WARNING: Keep the remote control battery away from children. It 

may cause a fire or chemical burn if mishandled. Do not recharge, 

disassemble, heat above 212ºF (100ºC), or incinerate. Dispose of a 

used battery promptly. Replace only with a battery of the correct type 

and model number. 

CAUTION: Danger of explosion if battery is incorrectly replaced. 

Replace only with an agency-approved (e.g. UL) CR2032 or 

DL2032 3-volt lithium battery.

1.  Place the remote face down on a flat surface.
2.  Using your finger, push the tab lock to the side as shown and 

hold. Slide the battery compartment open.

See operating

instructions for

 types of

battery to be used

e operating

nstructions for types of

battery to be used

WARNING: Do not ingest battery, chemical burn hazard. The remote 

control supplied with this product contains a coin/button cell battery. 

If the coin/button cell battery is swallowed it can cause severe internal 

burns in just two hours and can lead to death. Keep new and used 

batteries away from children. If the battery compartment does not 

close securely, stop using the product and keep it away from children. 

If you think the battery may have been swallowed or placed inside any 

part of the body seek immediate medical attention.

3.  Remove the old battery and install the new one with the plus 

(+) symbol facing up.

See operatin

g

instructions for types of

battery to be used

4.  Gently slide the battery compartment closed. It locks  

automatically.

Using this method you can set up your Wave

®

 SoundTouch™ 

 music system by first joining its own built-in Wi-Fi

®

 network, and 

then connecting to your home Wi-Fi network.
Note:  Use this method to set up your system as an AirPlay  device, 

only. To access the benefits of SoundTouch™, such as 

streaming Internet radio and your music services, you must 

add the system to your home Wi-Fi network using the 

SoundTouch™ app (see page 9).

1.  On the Wave

®

 SoundTouch™ music system remote, press the 

Power button to turn on the system.

2.  On the back of the SoundTouch™ pedestal, press and  

hold the Control button for about two seconds until  

ALTERNATE SETUP is displayed on the front panel.

3.  On your smart device, activate Wi-Fi and join the Bose

®

 

 SoundTouch™ Wi-Fi Network.

4.  Open a browser and type: http://192.168.1.1 in the address 

field.
The Wi-Fi setup window appears on the screen.

5.  Select your home Wi-Fi network from the drop-down list.
6.  Enter your password (if required) and tap or click Connect.

The SoundTouch™ pedestal attempts to connect to your home 

Wi-Fi network.
The Wi-Fi indicator on the rear panel of the SoundTouch™ 

 pedestal momentarily blinks white and then turns solid white 

when connected to the network.

7.  On your computer, tablet or smartphone, return to the Wi-Fi 

control panel and rejoin your home Wi-Fi network.

8.  Once the system is on the network, follow these steps to 

 complete  setup:
A.  Download and launch the SoundTouch™ app.  See 

 "Installing the SoundTouch™ app" on page 9.

B.  On the SOUNDTOUCH™ SYSTEM SETUP screen, select 

this option:
IT IS ALREADy ON my NETWORK

The SoundTouch

TM

 pedestal has built-in Wi-Fi capability that 

 enables it to wirelessly connect to your home Wi-Fi network. 
To disable Wi-Fi, press and hold the Control button on the back of 

the SoundTouch

TM

 pedestal for at least eight seconds or until the 

Wi-Fi status indicator turns off.
To enable Wi-Fi again, turn on the system.

The SoundTouch

™

 pedestal has a low-power standby mode in 

which it consumes a minimum amount of power. This can be used 

to reduce the power consumed in your home while you are away.
To place the SoundTouch

TM

 pedestal in the Power  saving mode, 

press and hold the Control button on the back of the  SoundTouch

TM

 

 pedestal for at least eight seconds or until the Wi-Fi status indicator 

turns off. This also disables the Wi-Fi capability.
To wake up the SoundTouch

TM

 pedestal, quickly press and release 

the Control  button. The Wi-Fi capability is enabled again when any 

source is selected.