Maytag MED4200BW Instruccion De Instalación

All dimensions show recommended and minimum spacing 

allowed. 

 

■

Additional spacing should be considered for ease of  

installation and servicing.

 

■

Additional clearances might be required for wall, door, floor 

moldings, and dryer venting.

 

■

Additional spacing should be considered on all sides of the 

dryer to reduce noise transfer.

 

■

For closet installation, with a door, minimum ventilation 

openings in the top and bottom of the door are required. 

Louvered doors with equivalent ventilation openings are 

acceptable.

 

■

Companion appliance spacing should also be considered.

 

■

To contact a qualified electrical installer.

 

■

To be sure that the electrical connection is adequate and  

in conformance with the National Electrical Code, ANSI/ 

NFPA 70 - latest edition and all local codes and ordinances. 

 

The National Electrical Code requires a 4-wire power supply 

connection for homes built after 1996, dryer circuits involved  

in remodeling after 1996, and all mobile home installations. 

 

A copy of the above code standards can be obtained from: 

National Fire Protection Association, One Batterymarch Park, 

Quincy, MA 02269.

 

■

To supply the required 3 or 4 wire, single phase, 120/240 

volt, 60 Hz, AC only electrical supply (or 3 or 4 wire, 120/208 

volt electrical supply, if specified on the serial/rating plate) 

on a separate 30-amp circuit, fused on both sides of the line. 

Connect to an individual branch circuit. Do not have a fuse in 

the neutral or grounding circuit.

 

■

Do not use an extension cord.

 

■

If codes permit and a separate ground wire is used, it is 

recommended that a qualified electrician determine that  

the ground path is adequate.

To properly install your dryer, you must determine the type of 

electrical connection you will be using and follow the instructions 

provided for it here.

 

■

This dryer is manufactured ready to install with a 3-wire 

electrical supply connection. The neutral ground conductor  

is permanently connected to the neutral conductor (white wire) 

within the dryer. If the dryer is installed with a 4-wire electrical 

supply connection, the neutral ground conductor must be 

removed from the external ground connector (green screw), 

and secured under the neutral terminal (center or white wire) 

of the terminal block. When the neutral ground conductor is 

secured under the neutral terminal (center or white wire) of the 

terminal block, the dryer cabinet is isolated from the neutral 

conductor. The green ground wire of the 4-wire power cord 

must be secured to the dryer cabinet with the green  

ground screw.

 

■

If local codes do not permit the connection of a neutral  

ground wire to the neutral wire, see “Optional 3-wire 

connection” section.

 

■

A 4-wire power supply connection must be used when the 

appliance is installed in a location where grounding through  

the neutral conductor is prohibited. Grounding through the 

neutral is prohibited for (1) new branch-circuit installations after 

1996, (2) mobile homes, (3) recreational vehicles, and (4) areas  

where local codes prohibit grounding through the neutral 

conductors.

Use a UL listed power supply cord kit marked for use with  

clothes dryers. The kit should contain:

 

■

A UL listed 30-amp power supply cord, rated 120/240 volt 

minimum. The cord should be type SRD or SRDT and be  

at least 4 ft. (1.22 m) long. The wires that connect to  

the dryer must end in ring terminals or spade terminals  

with upturned ends.

 

■

A UL listed strain relief.

This dryer is suitable for mobile home installations.  

The installation must conform to the Manufactured  

Home Construction and Safety Standard, Title 24 CFR, 

Part 3280 (formerly the Federal Standard for Mobile home 

construction and Safety, Title 24, HUD Part 280) or Standard 

CAN/CSA-Z240 MH.

 

■

Metal exhaust system hardware, available for purchase from  

your dealer. For further information, see “Assistance or  

Service” section in your “Use and Care Guide.”

 

■

Special provisions must be made in mobile homes to 

introduce outside air into dryer. Openings (such as a nearby 

window) should be at least twice as large as dryer exhaust 

opening.

* 0" (0 mm) spacing is allowed.