Bosch d9412gv3 Manual De Usuario
D9412GV3/D7412GV3 | Program Entry Guide | 2.0 Panel and Area Wide Parameters
EN | 65
Bosch Security Systems, Inc. | 10/11 | F01U170807-02
Reset Sensors
Default:
E
Selection: -, E, or P
Function
No.
No.
Function Name
Alternate
Keystroke
Keystroke
27 Reset
Sensors [COMMAND][4][7]
Use this function to activate the Reset Sensors
function for Fire or Intrusion points programmed as
P## Resettable in Section 3.1 Point Index on page
100. Points within the scope of the keypad where the
function is entered reset. Refer to Section 2.9.1
Keypad (Command Center) Assignment on page 50.
function for Fire or Intrusion points programmed as
P## Resettable in Section 3.1 Point Index on page
100. Points within the scope of the keypad where the
function is entered reset. Refer to Section 2.9.1
Keypad (Command Center) Assignment on page 50.
Change Relay
Default:
P
Selection: -, E, or P
Function
No.
No.
Function Name
Alternate
Keystroke
Keystroke
28 Change
Relays
[COMMAND][5][4]
Use this function to manually set and reset Relays 1
through 128 (1 through 64 in a D7412GV3) that are
installed in the system.
through 128 (1 through 64 in a D7412GV3) that are
installed in the system.
Remote Program
Default:
P
Selection: -, E, or P
Function
No.
No.
Function Name
Alternate
Keystroke
Keystroke
29
Remote
Programming
Programming
[COMMAND][4][3]
Use this function to start remote programming
software (RPS) sessions. When the phone is ringing
at the control panel, starting this function causes the
control panel to seize the line.
software (RPS) sessions. When the phone is ringing
at the control panel, starting this function causes the
control panel to seize the line.
Move to Area
Default:
P
Selection: -, E, or P
Function
No.
No.
Function Name
Alternate
Keystroke
Keystroke
30
Move to Area
[COMMAND][5][0]
Use this function to switch the keypad’s assignment
temporarily to a different area. This command can be
used to perform any function that can be performed
by a keypad assigned to the area in programming.
Users are limited to performing functions enabled by
the authority level they have in the area to which the
keypad is moved. After 15 sec of no activity at the
keypad, the keypad reverts back to the originally
programmed area.
temporarily to a different area. This command can be
used to perform any function that can be performed
by a keypad assigned to the area in programming.
Users are limited to performing functions enabled by
the authority level they have in the area to which the
keypad is moved. After 15 sec of no activity at the
keypad, the keypad reverts back to the originally
programmed area.
Display Rev
Default:
E
Selection: -, E, or P
Function
No.
No.
Function Name
Alternate
Keystroke
Keystroke
32
Display Software
Revision
Revision
[COMMAND][5][9]
Use this function to show the control panel’s software
revision number in the keypad display.
revision number in the keypad display.
Service Walk
Default:
P
Selection: -, E, or P
Function
No.
No.
Function Name
Alternate
Keystroke
Keystroke
33
Service Walk
Test
Test
(Menu function
only)
only)
Use this function to Walk Test all 246 points in the
entire control panel regardless of the P## Type.
entire control panel regardless of the P## Type.
The Service Walk Test is available on the
D9412GV3 using the Service Menu
[9][9][ENT]. The D7412GV3 does not
include the Service Walk Test in the
Service Menu. In the D7412GV3, the
Service Walk Test function must be
enabled in the Function List to access the
Service Walk Test.
D9412GV3 using the Service Menu
[9][9][ENT]. The D7412GV3 does not
include the Service Walk Test in the
Service Menu. In the D7412GV3, the
Service Walk Test function must be
enabled in the Function List to access the
Service Walk Test.