DELL NSA 5600 Manual De Usuario
58
| Safety and Regulatory Information
Safety and Regulatory Information
Safety Instructions
The following conditions are required for proper installation:
• The Dell SonicWALL appliance is designed to be mounted in a standard 19-inch
• The Dell SonicWALL appliance is designed to be mounted in a standard 19-inch
rack mount cabinet.
• Use the mounting hardware recommended by the rack manufacturer and ensure
that the rack is adequate for the application.
• Ensure that no water or excessive moisture can enter the unit.
• Allow unrestricted airflow around the unit and through the vents on the side of
• Allow unrestricted airflow around the unit and through the vents on the side of
the unit. A minimum of 1 inch (25.44mm) clearance is recommended.
• Route cables away from power lines, fluorescent lighting fixtures, and sources
of noise such as radios, transmitters, and broadband amplifiers.
• Mount in a location away from direct sunlight and sources of heat. A maximum
ambient temperature of 104º F (40º C) is recommended.
• If installed in a closed or multi-rack assembly, the operating ambient temperature
of the rack environment may be greater than the room ambient. Therefore,
consideration should be given to installing the equipment in an environment
compatible with the maximum recommended ambient temperature.
consideration should be given to installing the equipment in an environment
compatible with the maximum recommended ambient temperature.
• Mount the Dell SonicWALL appliances evenly in the rack in order to prevent a
hazardous condition caused by uneven mechanical loading.
• Four mounting screws, compatible with the rack design, must be used and hand-
tightened to ensure secure installation. Choose a mounting location where all
four mounting holes line up with those of the mounting bars of the 19-inch rack
mount cabinet.
four mounting holes line up with those of the mounting bars of the 19-inch rack
mount cabinet.
• A suitably rated and approved branch circuit breaker shall be provided as part of
the building installation. Follow local code when purchasing materials or
components.
components.
• Consideration must be given to the connection of the equipment to the supply
circuit. Appropriate consideration of equipment nameplate ratings must be used
when addressing this concern. Do not overload the circuit.
when addressing this concern. Do not overload the circuit.
• Reliable grounding of rack-mounted equipment must be maintained. Particular
attention must be given to power supply connections other than direct
connections to the branch circuits, such as power strips.
connections to the branch circuits, such as power strips.
• The included power cord is approved for use only in specific countries or regions.
Before using a power cord, verify that it is rated and approved for use in your
location.
location.
Lithium Battery Warning
The Lithium Battery used in the Dell SonicWALL Internet security appliance may
not be replaced by the user. The appliance must be returned to a Dell SonicWALL
authorized service center for replacement with the same or equivalent type
recommended by the manufacturer. If, for any reason, the battery or
Dell SonicWALL Internet security appliance must be disposed of, do so following
the battery manufacturer's instructions.
not be replaced by the user. The appliance must be returned to a Dell SonicWALL
authorized service center for replacement with the same or equivalent type
recommended by the manufacturer. If, for any reason, the battery or
Dell SonicWALL Internet security appliance must be disposed of, do so following
the battery manufacturer's instructions.
Cable Connections
All Ethernet and RS232 (Console) cables are designed for intra-building
connection to other equipment. Do not connect these ports directly to
communication wiring or other wiring that exits the building where the
Dell SonicWALL is located.
connection to other equipment. Do not connect these ports directly to
communication wiring or other wiring that exits the building where the
Dell SonicWALL is located.
Sicherheitsanweisungen
Für eine ordnungsgemäße Montage sollten die folgenden Hinweise beachtet
werden:
• Das Dell SonicWALL Modell ist für eine Montage in einem standardmäßigen 19-
werden:
• Das Dell SonicWALL Modell ist für eine Montage in einem standardmäßigen 19-
Zoll-Rack konzipiert.
• Vergewissern Sie sich, dass das Rack für dieses Gerät geeignet ist und
verwenden Sie das vom Rack-Hersteller empfohlene Montagezubehör.
• Stellen Sie sicher, dass das Gerät vor Wasser und hoher Luftfeuchtigkeit
geschützt ist.
• Stellen Sie sicher, dass die Luft um das Gerät herum zirkulieren kann und die
Lüftungsschlitze an der Seite des Gehäuses frei sind. Hier ist ein
Belüftungsabstand von mindestens 26 mm einzuhalten.
Belüftungsabstand von mindestens 26 mm einzuhalten.
• Achten Sie darauf, das sich die Netzwerkkabel nicht in der unmittelbaren Nähe
von Stromleitungen, Leuchtstoffröhren und Störquellen wie Funksendern oder
Breitbandverstärkern befinden
Breitbandverstärkern befinden
• Wählen Sie für die Montage einen Ort, der keinem direkten Sonnenlicht
ausgesetzt ist und sich nicht in der Nähe von Wärmequellen befindet. Die
Umgebungstemperatur darf nicht mehr als 40 °C betragen.
Umgebungstemperatur darf nicht mehr als 40 °C betragen.
Regulatory Model/Type
Product Name
1RK26-0A4
NSA 5600
1RK26-0A3
NSA 4600
1RK26-0A2
NSA 3600