White Rodgers 1F80ST-0471 Manual De Usuario

6

Set the VENT Switch to Auto or On.

Vent Auto is the most commonly selected setting and runs 
the fan only when the heating or cooling system is on.

Vent On runs the fan continuously for increased air circulation 
or to allow additional air cleaning.

Press the SISTEMA button to select:

Calor: Thermostat controls only the heating system.

Off: Heating and Cooling systems are off.

Frio: Thermostat controls only the cooling system.

Auto: Auto Changeover is used in areas where both heating 
and cooling may be required on the same day. Auto allows 
the thermostat to automatically select heating or cooling 
depending on the indoor temperature and the selected heat 
and cool temperatures. When using Auto, be sure to set the 
Cooling temperatures more than 1° Fahrenheit higher than 
the heating temperature.

Press the SISTEMA button to select Heat or Cool and use
the 

 or 

 buttons to adjust the temperature to your

desired setting. After selecting your desired settings you can
also press the SISTEMA button to select Auto to allow
the thermostat to automatically change between Heat and
Cool.

Press 

 or 

 and the Retener button and adjust the 

temperature wherever you like. This will override the program. 
The Retener feature bypasses the program and allows you 
to adjust the temperature manually, as needed. Whatever 
temperature you set in Retener will be maintained 24 hours 
a day, until you manually change the temperature or press 
Arrancar Programa (Run Schedule) to cancel Retener and 
resume the programmed schedule.

Press 

 or 

 buttons to adjust the temperature. This will 

override the temperature setting until the next programmed 
time. To cancel the temporary setting at any time and return 
to the program, press Arrancar Programa. If the SISTEMA 
button is pressed to select Auto the thermostat will change to 
Heat or Cool, whichever ran last. If it switches to heat but you 
want cool, or it changes to cool but you want heat, press both 

 and 

 buttons simultaneously to change to the other 

mode.

1. Press Menu and then Hora button once. The display 

will show the hour only.

2.  Press and hold either the 

 or 

 key until you reach 

the correct hour and AM/PM designation (AM begins at 
midnight, PM begins at noon).

3. Press Hora once again. The display window will show 

the minutes only.

4.  Press and hold either the 

 or 

 key until you reach 

the correct minutes.

5. Press Hora once again. The display will show the day 

of the week.

6. Press the 

 or 

 key until you reach the current day 

of the week.

7. Press Arrancar to exit the Time mode.

1. Press SISTEMA button to select "Calor" in the system  

switch area indicating the active mode being programmed.

2. Press the Menu button and then press Programa. 

3.  The top of the display will show the day(s) being 

programmed. The time and temperature (fl ashing) are also 
displayed. "1" will also be displayed to indicate the period.

4. Press 

 or 

 key to change the temperature to your 

selected temperature for the 1st heating period.

5. Press Hora button, time will fl ash.

6. Press 

 or 

 key to adjust the start time for the 

1st period.

7.  The time will change in 15 minute increments.

8.  After you have set the time and the temperature for  

the period to begin, press Schedule to advance to the 
next program period.

9.  Repeat steps 2 through 8 until all of the program times 

and temperatures are set for all program periods on  
that day. 

10. Press  Programa to the next day and repeat steps 2  

through 9.

11. When programming is complete and all of the times and  

temperatures match your desired heating schedule, press  
Run Schedule. The thermostat will now run your program.

1. Press SISTEMA button to select "Frio" in the system  

switch area indicating the active mode being programmed.

2. Follow Enter Heating Program instructions for entering 

cooling times and temperatures.