Behringer UMA25S Manual De Usuario

U-CONTROL UMA25S User Manual

(9)

(5)

(6)

(3)
(4)

(2)

(10)

(11)

(12)

(13)

(8)

(7)

(1)

Fig. 3.1: Top view of the UMA25S

(1) 

The keyboard of the UMA25S has 25 velocity-sensitive, full-size keys with 

half action.

(2) 

The OCT </> push buttons allow you to shift the keyboard range up to 

4 octaves up or down. These push buttons are also used for trans position 

(see Chapter 5.2.2).

(3) 

Press the MMC push button to use the default MMC (MIDI Machine Control) 

functions of the control elements E1 to E8. The MMC functions are printed on 

these control elements.

(4) 

Press the MUTE push button to suppress sending MIDI messages. This allows 

you to move control elements without changing the parameter values.

(5) 

Press the PRESET push button to load a preset.

(6) 

Press the EDIT/EXIT push button once to switch to Edit Mode. By pressing 

the button a second time, you exit Edit Mode without having accepted 

any changes.

(7) 

The –/+ push buttons let you select a preset. Press both buttons at the same 

time to silence stuck MIDI notes (PANIC).

(8) 

The 3-digit LED display briefly indicates the current firmware version when 

the keyboard is switched on, after which the selected preset number is 

displayed. In Play Mode, the display shows the value changes in real time 

when operating the control elements. In Edit Mode, the display shows the 

MIDI commands, program and channel numbers as well as parameter values.

(9) 

The PITCH BEND wheel (E17) lets you change the pitch in real time. This way 

a tone can be bent several semitones up or down while playing. The desired 

pitch interval is adjusted on the controlled device. The PITCH BEND wheel 

returns to the center position as soon as you let go of it.

(10) 

The MOD WHEEL (E18) works like a typical modulation wheel (MIDI CC 1). 

When you let go of the modulation wheel, it keeps the set value.

(11) 

The VOLUME slider (E19) controls the volume (MIDI Controller 07).

(12) 

The push buttons E1 – E8 can have any MIDI functions assigned to them. 

By pressing the MMC push button  

(3)

  once, these push buttons use the 

preconfigured transport control functions (see Chapter 5.5.7).

(13) 

The 8 high-resolution rotary knobs E9 – E16 generate Continuous 

Controller messages. In Edit Mode, the rotary knobs can be assigned to any 

controller number.

(14) (15) (16)

(17)

(18)

(19)

(20)

(21)

Fig. 3.2: Audio connectors on the rear panel

(14) 

If the Direct Monitor function is turned on (press switch  

(15)

), the MIX control 

allows you to adjust the volume level balance between the recording signal 

and the playback signal.

(15) 

The MONITOR ON/OFF switch activates the Direct Monitor function. 

The recording signal found at the MIC or LINE input is fed to the output 

connectors LINE OUT and PHONES in order to avoid latency and the resulting 

timing problems while recording.

(16) 

The LEVEL control lets you adjust the volume level of the headphone signal. 

Turn the control completely to the left before plugging in the headphones to 

avoid damage due to high volume levels.

(17) 

Plug the green headphone connector of the supplied headset into the 

PHONES connector.

(18) 

Plug the red connector of the headset or any dynamic microphone into the 

MIC IN connector.

(19) 

The LEVEL control adjusts the input volume of the microphone signal. 

Make sure the input signal does not clip (distortion).