Thermador PCG36 Instruccion De Instalación
English 10
All Installer supplied parts must conform to Local Codes.
*15 Amp 120 VAC electrical supply is required for 36" and 48" models with an electric griddle.
*15 Amp 120 VAC electrical supply is required for 36" and 48" models with an electric griddle.
Step 3: Unpacking, Moving, Placing and
Anchoring the Cooktop
Anchoring the Cooktop
CAUTION
Proper equipment and adequate manpower
must be used in moving the appliance to avoid
damage and/or personal injury. The unit is
heavy and should be handled accordingly.
must be used in moving the appliance to avoid
damage and/or personal injury. The unit is
heavy and should be handled accordingly.
Important
•
Verify that the appliance is correct for the type of gas
being provided. Refer to Step 4 before proceeding with
the installation.
being provided. Refer to Step 4 before proceeding with
the installation.
•
Attach the backguard before sliding the appliance into
the final installed position. See Step 6.
the final installed position. See Step 6.
•
Remove the outer carton and packing material from the
shipping base. Ensure that you have all cooktop
components before proceeding.
shipping base. Ensure that you have all cooktop
components before proceeding.
•
Remove the top grate castings and burner caps to
reduce cooktop’s weight.
reduce cooktop’s weight.
NOTE:
Leave adhesive-backed foam layer over brushed-metal
surfaces, to protect finish from scratches, until the cooktop
is installed in its final position.
Leave adhesive-backed foam layer over brushed-metal
surfaces, to protect finish from scratches, until the cooktop
is installed in its final position.
•
Lift and place the cooktop in the opening. Be careful
not to pinch the power cord or gas inlet. Care should be
used not to scratch the griddle cooking plate.
not to pinch the power cord or gas inlet. Care should be
used not to scratch the griddle cooking plate.
•
Make sure that the power cord is free and hanging
loose.
loose.
•
The cooktop must be level for proper performance.
•
Replace the cooking grates and burner caps. Ensure
that the burner caps are correctly seated on the burner
bases.
that the burner caps are correctly seated on the burner
bases.
Griddle Tilt Adjustment (not all models)
Check the griddle adjustment by pouring two tablespoons
of water on the back of the griddle plate. The water should
slowly roll into the grease tray. If not, adjust the two screws
under the back of the plate. Start with one half turn counter-
clockwise (CCW) of the screws. Further adjustment should
be made by one-quarter turn until water slowly flows into
the grease tray.
of water on the back of the griddle plate. The water should
slowly roll into the grease tray. If not, adjust the two screws
under the back of the plate. Start with one half turn counter-
clockwise (CCW) of the screws. Further adjustment should
be made by one-quarter turn until water slowly flows into
the grease tray.
Figure 9: Bottom of Unit
Product Rating
Label/Serial Tag
Label/Serial Tag
Threading compounds must be
resistant to Propane Gas
resistant to Propane Gas
1/2" NPT
gas flow
3/4” flex line
3” Min.
Power
Cord or
Conduit
A manual valve must be installed
external to the appliance, in an acces-
sible location from the front, for the
purpose of shutting off the gas supply.
external to the appliance, in an acces-
sible location from the front, for the
purpose of shutting off the gas supply.
3-Prong grounding type receptacle
connected to a properly grounded and
polarized electrical supply rated at 120VAC,
10 Amps, (or 15A*) Single Phase, 60 HZ.
connected to a properly grounded and
polarized electrical supply rated at 120VAC,
10 Amps, (or 15A*) Single Phase, 60 HZ.