Glen Dimplex Home Appliances Ltd BE813 Manual De Usuario
ELECTRICAL REQUIREMENTS
Before you insert the plug into the wall socket make sure that the voltage and
the frequency shown in the rating plate inside the appliance corresponds to
your electricity supply. Rating label is on the left hand side of fridge liner.
We recommend that this appliance is connected to the mains supply via a
suitable switched and fused socket in a readily accessible position.
Should the mains lead of the appliance become damaged or should it need
replacing at any time, it must be replaced by a special purpose made mains
lead which can only be obtained from a Belling Authorised Service Agent.
Before you insert the plug into the wall socket make sure that the voltage and
the frequency shown in the rating plate inside the appliance corresponds to
your electricity supply. Rating label is on the left hand side of fridge liner.
We recommend that this appliance is connected to the mains supply via a
suitable switched and fused socket in a readily accessible position.
Should the mains lead of the appliance become damaged or should it need
replacing at any time, it must be replaced by a special purpose made mains
lead which can only be obtained from a Belling Authorised Service Agent.
WARNING! THIS APPLIANCE MUST BE EARTHED
If the fitted moulded plug is not suitable for your socket, then the plug should
be cut off and an appropriate plug fitted. Destroy the old plug which is cut off
as a plug with bared cord could cause a shock hazard if inserted into a socket
elsewhere in the house.
The moulded plug on this appliance incorporates a 13 A fuse. Should the fuse
need to be replaced an ASTABEAB approved BS 1362 fuse of the same rating
must be used. Do not forget to refit the fuse cover. In the event of losing the
fuse cover the plug must not be used until a replacement fuse cover has been
fitted. Colour of the replacement fuse cover must be the same colour as that
visible on the pin face of the plug. Fuse covers can be obtained from a Belling
authorised service agent.
If the fitted moulded plug is not suitable for your socket, then the plug should
be cut off and an appropriate plug fitted. Destroy the old plug which is cut off
as a plug with bared cord could cause a shock hazard if inserted into a socket
elsewhere in the house.
The moulded plug on this appliance incorporates a 13 A fuse. Should the fuse
need to be replaced an ASTABEAB approved BS 1362 fuse of the same rating
must be used. Do not forget to refit the fuse cover. In the event of losing the
fuse cover the plug must not be used until a replacement fuse cover has been
fitted. Colour of the replacement fuse cover must be the same colour as that
visible on the pin face of the plug. Fuse covers can be obtained from a Belling
authorised service agent.
IMPORTANT! FITTING A DIFFERENT PLUG
As the colours of the wires in the mains lead of this appliance may
not correspond with the coloured
markings identifying the terminals
in your plug proceed as follows:
(See diagram).
1. Connect the green-yellow or
green (Earth) wire to the terminal
in the plug marked 'E' or with the
As the colours of the wires in the mains lead of this appliance may
not correspond with the coloured
markings identifying the terminals
in your plug proceed as follows:
(See diagram).
1. Connect the green-yellow or
green (Earth) wire to the terminal
in the plug marked 'E' or with the
symbol
or coloured green and
yellow or green.
2. Connect the blue (Neutral) wire
to the terminal in the plug marked
'N' or coloured black.
3. Connect the brown (Live) wire
to the terminal in the plug marked
'L' or coloured red.
With alternative plugs a 13 A fuse
must be fitted either in the plug or
adaptor or in the main fuse box. If
in doubt contact a qualified electrician.
2. Connect the blue (Neutral) wire
to the terminal in the plug marked
'N' or coloured black.
3. Connect the brown (Live) wire
to the terminal in the plug marked
'L' or coloured red.
With alternative plugs a 13 A fuse
must be fitted either in the plug or
adaptor or in the main fuse box. If
in doubt contact a qualified electrician.
3
FITTED WITH
BS 1362 13A
FUSE
AL
W
A
YS
FIT
BS 1362 REPLACEMENT
CAR
TRIDGE FUSE
GREEN
&
YELLOW
OR
GREEN
N
BLUE
OR
BLACK
L
BROWN
OR
RED
22mm.
6mm.
6mm.
6mm.
32mm.
12mm.
FUSE
CORD GRIP