U-Line BI95 Uso Y Cuidado
BI95, BI98, SP18
7
Model SP18
To turn the unit on or off, press the rocker switch (Figure
3) located in the center of the lower grille.
3) located in the center of the lower grille.
Ice Harvest Control
Adjustments are not normally needed. The control is
preset at the factory.
preset at the factory.
IMPORTANT
IMPORTANT
Making adjustments may affect the daily ice
production of the unit.
production of the unit.
Figure 4
Models 95 and 98
To adjust the Ice Harvest Control:
1. Remove the front grille (one screw) (Figure 4, 1).
Figure 5
2. Turn the adjusting screw (Figure 5) using a flat tip
screwdriver in a small increment clockwise for a COLDER
setting (slower ice production) or counterclockwise for
a WARMER setting (faster ice production).
setting (slower ice production) or counterclockwise for
a WARMER setting (faster ice production).
3. Replace the front grille (one screw).
Model SP18
Model SP18 has a factory preset Ice Harvest Control that is
optimized for ice production, and is not adjustable.
optimized for ice production, and is not adjustable.
Ice Maker
When the ice bucket is full, the ice making mechanism will
shut off. However, the refrigeration system will continue
to cool and maintain the cube supply.
shut off. However, the refrigeration system will continue
to cool and maintain the cube supply.
IMPORTANT
IMPORTANT
Do not place cans or bottles in the ice compartment
because they will freeze.
because they will freeze.
Figure 6
Ice production may be interrupted by raising the bin arm
into an upright and locked position (Figure 6). The unit
will maintain temperature for ice storage.
into an upright and locked position (Figure 6). The unit
will maintain temperature for ice storage.
IMPORTANT
IMPORTANT
If you are not intending to use the ice maker and
turn the supply valve off, it is imperative to raise
the bin arm of the ice maker (Figure 6). Failure to
raise the bin arm may result in damage to the water
valve.
turn the supply valve off, it is imperative to raise
the bin arm of the ice maker (Figure 6). Failure to
raise the bin arm may result in damage to the water
valve.
Certain sounds are normal during the unit’s operation.
You may hear the compressor or fan motor, the water
valve, or ice dropping into the ice bucket.
You may hear the compressor or fan motor, the water
valve, or ice dropping into the ice bucket.
WARNING
NEVER use an ice pick, knife or other sharp
instrument to separate cubes. Shake the ice
bucket instead.
instrument to separate cubes. Shake the ice
bucket instead.
During periods of limited usage or high ambient
temperatures, it is common for cubes to fuse together.
Shake the bucket to break apart cubes. If the ice maker is
not used regularly, the ice bucket should be emptied
periodically to ensure fresh cubes.
temperatures, it is common for cubes to fuse together.
Shake the bucket to break apart cubes. If the ice maker is
not used regularly, the ice bucket should be emptied
periodically to ensure fresh cubes.
It is normal for cubes to appear cloudy. This is caused by
air being trapped in the water due to fast freezing. It has
nothing to do with the health, taste or chemical make-up
of the water. It is the same air that is in every glass of
water you drink.
air being trapped in the water due to fast freezing. It has
nothing to do with the health, taste or chemical make-up
of the water. It is the same air that is in every glass of
water you drink.
The ice bucket can be removed for emptying and
cleaning. To remove the ice bucket, raise the bin arm and
remove the bucket from the ice compartment. Use the ice
bucket for ice storage only.
cleaning. To remove the ice bucket, raise the bin arm and
remove the bucket from the ice compartment. Use the ice
bucket for ice storage only.
1
2
ULIN_0027_A
C
OLDER
ULIN_0131_A
ULIN_0087_A