U-Line B195 Manual De Usuario
Level & Install Unit
16
12 Install
Leveling Information
ADA15IM & BI2115
It is recommended that the unit is level.
1. Use a level to check the
levelness of the unit from
front to back and from side
to side. Level should be
placed along top edge and
side edge as shown
front to back and from side
to side. Level should be
placed along top edge and
side edge as shown
2. If the unit is not level, adjust
the feet on the corners of
the unit as necessary (not
available in all models).
the unit as necessary (not
available in all models).
3. Check the levelness after each adjustment and repeat the
previous steps until the unit is level.
INSTALLATION TIP
If the room floor is higher than the floor in the cut-out opening,
adjust the rear feet to achieve a total unit rear height of 1/8" less
than the opening’s rear height. Shorten the unit height in the front
by adjusting the front feet. This allows the unit to be gently tipped
into the opening. Readjust the front feet to level the unit after it is
correctly positioned in the opening.
adjust the rear feet to achieve a total unit rear height of 1/8" less
than the opening’s rear height. Shorten the unit height in the front
by adjusting the front feet. This allows the unit to be gently tipped
into the opening. Readjust the front feet to level the unit after it is
correctly positioned in the opening.
All Other Models
IMPORTANT
IMPORTANT
It is extremely important that these units sit on a level
surface, as they do not have feet levelers. If they are not
level, the ice mold will not fill evenly.
surface, as they do not have feet levelers. If they are not
level, the ice mold will not fill evenly.
Use a level to check the
levelness of the unit from front
to back and from side to side.
Level should be placed along
top edge and side edge as
shown.
levelness of the unit from front
to back and from side to side.
Level should be placed along
top edge and side edge as
shown.
1
Turn Foot to Adjust
Installation
1. Open the water supply valve in the main water source.
2. Plug in the powercord.
3. Gently push the unit into position. Be careful not to kink the
water supply line or entangle the electrical cord.
4. Re-check the leveling, from front to back and side to side. Make
any necessary adjustments. The unit’s top surface should be
approximately 1/8" below the countertop.
approximately 1/8" below the countertop.
Grille Installation
BI95, BI98, WH95TP, BCM95BTP, BCM95
1. Locate and remove the grille screw from the cabinet, using a
standard blade screwdriver (or a 1/4" nut driver).
2. Identify the grille screw hole on the grille itself. It is located
toward the top of the middle recessed section of the grille.
3. Place the two hook-hinges (located on the rear bottom side of
the grille) onto the front lip of the unit base. Swing the grille up
into position, aligning the grille screw hole on the grille to the
grille screw hole on the cabinet. See Below.
into position, aligning the grille screw hole on the grille to the
grille screw hole on the cabinet. See Below.
4. Insert the screw. Do not overtighten.
SS1095 Models
SS1095NF & SS1095FC models: Place the bottom lip of the grille
on the inside of the base pan and swing grille up into position.
on the inside of the base pan and swing grille up into position.
SS1095FD model: Align the tabs on the bottom of the grille with
the slots in the flange and swing grille up into position.
the slots in the flange and swing grille up into position.
Align the grille and cabinet screw holes.
Insert the grille screw and tighten. Do not over-tighten
1
Grille Screw
Hook-Hinge
Unit Base
Front Lip
Grille
Model:
SS109FD
SS109FD
Models:
SS1095NF & SS1095FC
SS1095NF & SS1095FC
Insert This Lip Behind Base Plate Lip
Align Tab
With Slots
With Slots