Cisco Systems Intelligent Gigabit Ethernet Switch Module Manual De Usuario
44
Cisco Systems Intelligent Gigabit Ethernet Switch Module for the IBM
E
server BladeCenter System Message Guide
UDLD-3-UDLD_INTERNAL_IF_ERROR: UDLD internal error, interface [chars]:[chars].
Explanation This message means that a software check failed during UDLD processing. The first
[chars] is the interface, and the second [chars] is a description of the error.
[chars] is the interface, and the second [chars] is a description of the error.
Response
Find out more about the error by using the show tech-support privileged EXEC command and
by copying the error message exactly as it appears on the console or system log and entering it in the Output
Interpreter tool. Use the Bug Toolkit to look for similar reported problems. For more information about these
online tools , see the
Interpreter tool. Use the Bug Toolkit to look for similar reported problems. For more information about these
online tools , see the
UDLD-4-UDLD_PORT_DISABLED: UDLD disabled interface [chars], [chars] detected.
Explanation This message means that the UDLD Protocol disabled an interface because it detected
connections between neighbors that were functioning only in one direction, which might potentially cause
spanning-tree loops or interfere with connectivity. The cause is likely to be hardware related, either due to
a bad port, a bad cable, or a misconfigured cable. The first [chars] is the interface, and the second [chars]
is the error detected.
connections between neighbors that were functioning only in one direction, which might potentially cause
spanning-tree loops or interfere with connectivity. The cause is likely to be hardware related, either due to
a bad port, a bad cable, or a misconfigured cable. The first [chars] is the interface, and the second [chars]
is the error detected.
Response
Try to correct the configuration or locate the bad cable. If you are not successful, find out more
about the error by using the show tech-support privileged EXEC command and by copying the error message
exactly as it appears on the console or system log and entering it in the Output Interpreter tool. Use the Bug
Toolkit to look for similar reported problems. For more information about these online tools , see the
exactly as it appears on the console or system log and entering it in the Output Interpreter tool. Use the Bug
Toolkit to look for similar reported problems. For more information about these online tools , see the
.
UDLD-6-UDLD_PORT_RESET: UDLD reset interface [chars].
Explanation This message means that the UDLD Protocol detected a unidirectional connection between
neighbors. You reset the port that was disabled by UDLD by using the udld reset privileged EXEC
command or through a hardware action such as a link-state change. [chars] is the interface.
neighbors. You reset the port that was disabled by UDLD by using the udld reset privileged EXEC
command or through a hardware action such as a link-state change. [chars] is the interface.
Response
Find out more about the error by using the show tech-support privileged EXEC command and
by copying the error message exactly as it appears on the console or system log and entering it in the Output
Interpreter tool. Use the Bug Toolkit to look for similar reported problems. For more information about these
online tools , see the
Interpreter tool. Use the Bug Toolkit to look for similar reported problems. For more information about these
online tools , see the
UFAST_MCAST_SW Messages
This section contains the UplinkFast multicast software (UFAST_MCAST_SW)
messages. The switch sends these messages when UplinkFast is enabled, a new root
port takes over, and fast relearn multicast packets are not sent.
messages. The switch sends these messages when UplinkFast is enabled, a new root
port takes over, and fast relearn multicast packets are not sent.
UFAST_MCAST_SW-3-PROC_START_ERROR: No process available for transmitting UplinkFast packets.
Explanation This message means that no process is available for sending UplinkFast packets.
Response
Reload the switch by using the reload privileged EXEC command. If this problem continues
after you reload the switch, find out more about the error by using the show tech-support privileged EXEC
command and by copying the error message exactly as it appears on the console or system log and entering
it in the Output Interpreter tool. Use the Bug Toolkit to look for similar reported problems. For more information
about these online tools , see the
command and by copying the error message exactly as it appears on the console or system log and entering
it in the Output Interpreter tool. Use the Bug Toolkit to look for similar reported problems. For more information
about these online tools , see the