Barracuda Networks Network Hardware Prospecto

To avoid unauthorized use, Barracuda Networks recommends that you change the default root

password to a more secure password.
• Go to

Config

System

• Within the

Root

Password

section, enter the old (ngf1r3wall) and afterwards the new root

password with at least 5 characters.

• Click

Send Changes

followed by

Activate

Note:

Even if the root password is changed as described here, if the appliance does not have

a valid license, the default root password will still be valid for root login. Please see

instructions below for how to install a valid license

Appliance models

F10

F30x

use

PORT4

for the ISP by default.

If your ISP assigns the WAN IP address through the DHCP protocol, simply connect the modem to

PORT4

. This port is pre configured to be used with an ISP using DHCP.

For all other models the network port can be chosen individually and the settings for ISP

configuration must be done manually:

• Navigate to:

Config

Network

xDSL/ISDN/DHCP

• Enable one of the available WAN connection types and configure it according to the settings

provided by your Internet Service Provider.

• To check if the WAN IP address assignment was successful, navigate to

Control

Network

The Barracuda NG Admin application automatically obtains and installs your licenses from

Barracuda Networks. For this procedure, the Barracuda NG Admin application needs to have a

connection to the internet.

This process automatically starts, as soon as you login to your Barracuda NG Firewall.

You will be guided through the activation process and need to fill out a customer information form.

The current license and activation state is displayed on the

Status

page.

7. Firewall Rule Set Configuration

By default the Barracuda NG Firewall blocks all connections from and to the Internet.

To enable Internet access for the trusted LAN, the default firewall rules need to be enabled and

reordered properly.
• Navigate to

Config

> (

Simple Config

) >

Ruleset

• Use drag&drop and move the

BLOCKALL

rule to the bottom of the list.

• Double click the

LAN-2-Internet

rule and un-check the

Deactivate Rule

checkbox.

• Click

Send Changes

followed by

Activate

5. Change Default Password

6. Connect ISP

8. Product Activation

9. Change Management IP & Network

After the initial configuration, it may be necessary to change to management IP address and the

management network of your Barracuda NG Firewall, to be integrated into an existing network

environment.
• Navigate to:

Config

Network

Networks

• Change the

Management IP (MIP)

to the desired IP address within the existing network.

• Set the

Associated Netmask

• Click

Send Changes

followed by

Activate

Changing network settings, require an explicit activation within the network subsystem.

• Navigate to:

Control

Box

Network

• Click

Activate new network configuration

and select

Force

as activation mode.

After a few moments you will be able to connect to the new management IP address. Do not forget

to change the network configuration of your personal computer.

10. Package Contents

Contents

F10 F10x F20x F30x F400 F600 F800 F900

Security Appliance

Power Cord

External Power Supply

Ethernet Crossover Cable (red)

Ethernet Standard Cable (grey)

Serial Cable (console)

USB Thumb Drive

WiFi Antenna

Rack Mount Brackets

Rack Mount Rail Kit

F101/F201 and F301 only

Contact and Copyright Information

Barracuda Networks, Inc. 3175 S. Winchester Blvd, Campbell, CA 95008 USA • phone: 408.342.5400 • fax: 408.342.1061 •

subject to license. Information in this document is subject to change without notice. Barracuda NG Firewall is a trademark of Barracuda

Networks, Inc. All other brand and product names mentioned in this document are registered trademarks or trademarks of their

respective holders. v5.2.0-260411-02-250711

• For additional information and product documentation, visit:

www.barracudanetworks.com/doc