Coleman 2000000143 Prospecto

Attaching Room Divider

1. Room divider panel can be installed by inserting toggles

through the fabric loops. (Fig. 19 & 20)

The Coleman Company, Inc. • 3600 N. Hydraulic • Wichita, Kansas 67219

1-800-835-3278 • www.coleman.com

MADE IN CHINA • PRINTED IN CHINA

Coleman

and are registered trademarks of The Coleman Company, Inc.

Things You Should Know:

• Under certain conditions (cold weather, high humidity, etc.) condensa-

tion will form on the inside of your tent. Condensation is caused by
water vapor from your breath, perspiration, or any wet clothing inside
the tent. It is NOT LEAKAGE through the tent fabric. It can be minimized
by removing wet clothing from your tent and by providing good ventila-
tion through the tent.

• Never store tent, even for a short period of time, without drying it

thoroughly and brushing off caked dirt. Do not pack stakes or poles
inside your tent. Use a separate storage bag.

• Stakes should be removed by pulling on the stake itself. Never pull on

the tent to remove stake.

• TENT POLES SHOULD NOT BE LEFT TELESCOPED TOGETHER

DURING STORAGE.

• Do not leave your tent set-up for weeks at a time. Be aware that exposure

to ultraviolet rays from the sun can seriously damage material and/or
cause it to become discolored.

WARNING: Keep all flame and heat sources away

from this tent fabric.

This tent meets the flammability requirements of CPAI-84. The fab-
ric may burn if left in continuous contact with any flame source.
The application of any foreign substance to the tent fabric may
render the flame-resistant properties ineffective.

To Attach Rainfly

continued

2. Clip hooks on elastic

cords on rainfly to rings
at bottom of tent. (Fig. 12)

Fig. 16

To Store

1. All metal poles and stakes must to be placed in the storage

bag to prevent damage to the fabric items placed in the
carry case.

2. Make sure tent is clean and dry before placing in carry case.
3. Remove rainfly, spread out on floor of tent, then unzip

door & vents before taking tent down for storage.

4. Neatly fold tent to width of pole storage bag, place on tent,

roll tightly, and place in carry case.

5. Store in a clean, dry area.

Cooler Access

The smaller zippered opening at the side of the tent is designed
for added ventilation and easy access to your beverage cooler.
1. To use as a vent, unzip flap to

expose screen. (Fig.18)

2. To use as a cooler access, unzip

other flap to make an avenue to
bring beverages into the tent.
(Fig.23)

Fig. 23

Fig. 20

Fig. 19

STITCH LINE

Electrical Cord Access

1. Unzip access panel in the lower

right corner of tent and bring in
electrical cord. Use only UL
approved cords that are rated for
outdoor usage. (Fig. 22)

Fig. 22

Fig. 12

3. Secure rainfly with hook & loop

fasteners located on underside of fly
to gray and black poles. (Fig 13)

Fig. 13

Fig. 15

4. Assemble black, shock-

corded, rainfly pole
and slide through sleeve
on underside of rainfly.
(Fig 14)

5. Insert ends of rainfly

into brass grommets on
tent to form an arch
over doorway. (Fig. 15)

Fig. 14

COMPLETED TENT

Overhead Storage

1. Convenient overhead stor-

age compartment is located
at the back of the tent.
(Fig. 21)

2. Small storage pockets are

located on each side of tent.

6. Tie guylines at 4 locations (2 on

front, 2 on back) of tent and secure
with stakes.
(Fig. 16 & 17)

Tie Guylines

Fig. 17

7. To open door fully, unzip, then roll up

and insert toggle through fabric loop.
(Fig. 18)

8. To use the door vent, undo other

zipper to expose vent, then roll up
door flap and fasten with toggle and
fabric loop.

Fig. 18

Fig. 21

Rev09/07