Panasonic KX-TG6473 Manual De Usuario
Programming
25
For assistance, please visit http://www.panasonic.com/help
sleeping. Silent mode can be set for
each handset.
each handset.
Important:
L
Set the date and time beforehand
(page 13).
(page 13).
L
We recommend turning the base unit
ringer off (page 15) and call screening
off (page 31) in addition to turning the
silent mode on.
(KX-TG6421 series: page 3)
ringer off (page 15) and call screening
off (page 31) in addition to turning the
silent mode on.
(KX-TG6421 series: page 3)
L
If you have set the alarm, the alarm
sounds even if the silent mode is
turned on.
sounds even if the silent mode is
turned on.
Turning silent mode on/off
1
{
MENU} i {#}{2}{3}{8}
2
{V}
/{^}: Select “On” or “Off”. i
{
SAVE}
L
If you select “Off”, press {OFF}
to exit.
to exit.
3
Enter the desired hour and minute
you wish to start this feature.
you wish to start this feature.
4
{
AM/PM}: Select “AM” or “PM”. i
{
OK}
5
Enter the desired hour and minute
you wish to end this feature.
you wish to end this feature.
6
{
AM/PM}: Select “AM” or “PM”.
7
{
SAVE} i {OFF}
L
When the silent mode is set,
& is
displayed.
Note:
L
To correct a digit, press {^} or {V} to
move the cursor to the digit, then
make the correction.
move the cursor to the digit, then
make the correction.
Changing the start and end time
1
{
MENU} i {#}{2}{3}{7}
2
Continue from step 3, “Turning
silent mode on/off”, page 25.
silent mode on/off”, page 25.
Call block (Caller ID
subscribers only)
subscribers only)
This feature allows the unit to reject calls
when:
when:
– the unit receives a call from a phone
number stored in the call block list as
unwanted (“Storing unwanted callers”,
page 25).
unwanted (“Storing unwanted callers”,
page 25).
– the unit receives a call without phone
When a call is received, the unit rings for
a short time while the caller is being
identified. If the unit recognizes the call
as unwanted, “Caller blocked” is
displayed and the unit sends out a busy
tone to the caller, and then disconnects
the call.
a short time while the caller is being
identified. If the unit recognizes the call
as unwanted, “Caller blocked” is
displayed and the unit sends out a busy
tone to the caller, and then disconnects
the call.
Important:
L
When the unit receives a call from a
number that is stored in the call block
list or a call without a recognized
phone number, the call is logged in the
caller list (page 29) with
number that is stored in the call block
list or a call without a recognized
phone number, the call is logged in the
caller list (page 29) with
$ after the
call is disconnected.
Storing unwanted callers
You can store up to 30 phone numbers in
the call block list by using the caller list or
by entering the numbers directly.
You can store up to 30 phone numbers in
the call block list by using the caller list or
by entering the numbers directly.
Important:
L
You must store the phone number
with an area code (10 digits) in the call
block list.
with an area code (10 digits) in the call
block list.
■ From the caller list:
1
{
MENU} i {#}{2}{1}{3}
2
{V}
/{^}: Select the entry to be
blocked.
L
To edit the number, press
{
{
EDIT} repeatedly until the
phone number is shown in the
10-digit format.
10-digit format.
3
{
SAVE}
TG640x(e).book Page 25 Wednesday, November 26, 2008 2:33 PM