Panasonic KX-TG2302 Manual De Usuario

After your Panasonic battery is fully charged, you can expect the
following performance:

When the RECHARGE indicator flashes or
the handset beeps intermittently, place the
handset on the base unit for 6 hours to
recharge the battery.

•The RECHARGE indicator will flash when the handset battery is

charged less than 15 minutes and the handset is lifted off the base unit.

RECHARGE
Indicator

•A fully charged battery will give you up to 5 hours of continuous talk

time, or keep your handset in Standby mode to receive incoming calls
for up to 11 days (if no phone calls are made). Battery power is
consumed whenever the handset is off of the base unit, even when the
handset is not in use. The longer you leave the handset off of the base
unit, the time you can actually talk on the handset will be shortened.
Actual battery performance depends on a combination of how often
the handset is in TALK mode and how often it is in Standby mode.

•If the battery is fully charged, you do not have to place the handset

on the base unit until the RECHARGE indicator flashes. This will
maximize the battery life.

•If you want to keep the battery fully charged at all times, place the

handset on the base unit when the handset is not used. The battery
cannot be overcharged.

•Clean the charge contacts of the handset and the base unit with

a soft, dry cloth once a month. Clean more often if the unit is
subject to grease, dust or high humidity. Otherwise the battery
may not charge properly.

You can hang the handset on your belt or pocket using the included
belt clip.

Battery replacement:
If you cleaned the charge contacts and fully charged the battery, but
after a few telephone calls, the RECHARGE indicator flashes, the
battery may need to be replaced. Please order a new Panasonic 
HHR-P104 battery at the telephone number shown on section 1-A. 
To replace the battery, see section 1-C, step 2.

A nickel metal hydride battery that is recyclable
powers the product you have purchased. Please call
1-800-8-BATTERY for information on how to recycle
this battery.

While in use (TALK)

Up to about 5 hours

Up to about 11 days

While not in use (Standby)

Press [FLASH/CALL WAIT] if you hear a call waiting tone during a
conversation.
•The first call is put on hold and you can answer the second call.

•To return to the first caller, press [FLASH/CALL WAIT] again.

•If this function does not operate properly, consult your telephone

company for details.

Press [ ] (TONE) before entering access numbers which require
tone dialing. 
•The dialing mode changes to tone. You can enter numbers to

access an answering service, electronic banking service, etc.
When you hang up, the dialing mode will return to pulse.

You can locate the handset or page the handset user with beep
tones from the base unit.

1. Press [HANDSET LOCATOR] on the base unit.

•The TALK indicator on the handset and the IN USE indicator on

the base unit flash rapidly, and the handset beeps for 1 minute.

2. To stop paging, press [HANDSET LOCATOR] again or press

[OFF] on the handset.
•You can also stop paging on the handset by pressing any

button except [

▼] or [▲].

Pressing [FLASH/CALL WAIT] allows you to use special features of
your host PBX such as transferring an extension call, or accessing
optional telephone services such as call waiting.
•Pressing [FLASH/CALL WAIT] cancels Temporary Tone Dialing mode.

If an alarm tone sounds when you press [

], [SP-PHONE] or

[VOICE ENHANCER] even when using the handset near the base
unit, the handset may have lost communication with the base unit.
You need to re-register the handset to the base unit.

•Have both the handset and base unit nearby during registration.

•Follow steps 1 and 2 listed below. You have about 1 minute to

1.

Base unit: Press and hold [HANDSET LOCATOR].
•The CHARGE indicator flashes.

2. Handset: Press and hold [FLASH/CALL WAIT] until a beep

sounds.
•The VOICE ENHANCER indicator flashes.

•When registration is complete, a beep sounds from the handset

and the indicator lights go out.

•Wait for 20 seconds after registration is complete while the

•If the handset beeps 3 times in step 2, an error occurred. Try again

from step 1.

•You can stop registration by pressing [OFF] on the handset, and

pressing [HANDSET LOCATOR] on the base unit.