Panasonic KX-TG2503S Manual De Usuario

Operating near 2.4GHz electrical appliances may cause interference. Move
away from the electrical appliances and/or press the CH (Channel) button.

The AC adaptor is used as the main disconnect device, ensure that the AC
outlet is located/installed near the unit and is easily accessible.
• Environment—do not place the unit in a room where the temperature is

less than 5°C (41°F) or greater than 40°C (104°F). Allow 10 cm (4")
clearance around the unit for proper ventilation. Avoid excessive smoke,
dust, mechanical vibration, shock, or direct sunlight.

• Medical—consult the manufacturer of any personal medical devices,

such as pacemakers, to determine if they are adequately shielded from
external RF (radio frequency) energy. (The unit operates in the
frequency range of 2401MHz to 2472MHz, and the power output level
can range from 0.001 watts to 0.20 watts.) Do not use the unit in health
care facilities if any regulations posted in the area instruct you not to do
so. Hospitals or health care facilities may be using equipment that could
be sensitive to external RF (radio frequency) energy.

• Routine care—wipe the unit with a soft cloth. Do not use benzine,

thinner, or any abrasive powder. When you leave the unit unused for a
long period of time, unplug the AC adaptor from the outlet.

• If there is any trouble—disconnect the unit from the telephone line 

and connect a known working phone. If the known working phone
operates properly, have your unit repaired by one of the authorized
Panasonic Factory Service Centers. If the known working phone does
not operate properly, consult your telephone company.

Caution:
To comply with FCC RF exposure requirements, the base unit should be
installed with its antenna located at 20 cm or more from persons and
handset should be carried with the specific belt-clip provided for the
handset to ensure compliance. Other non-tested belt-clips or similar body-
worn accessories may not comply, therefore, should be avoided.

(REDIAL)

(HANDSET!LOCATOR)

•Check the settings (1-C).

•Charge the battery fully (6-A).

•Clean the charge contacts and charge

again (6-A).

•Install the battery properly (6-B).

•Place the handset on the base unit and

unplug the AC adaptor to reset. Plug in,
and try again.

•Re-install the battery and place the

handset on the base unit. Try again.

•You are too far from the base unit. Move

closer and try again.

•Place the handset on the base unit and try

again.

•Plug in the AC adaptor.

•Raise the base unit antennas.
•Locate the handset and the base unit

away from other electrical appliances 
(6-D).

•Move closer to the base unit.

•Raise the base unit antennas.

•Press 

(CH)

to select a clearer channel.

•The ringer volume is set to OFF. Press 

Ñ

or 

Ö

while the TALK indicator light is off

(2-B).

•To answer the call, press 

(TALK)

. The

program will be canceled. Store the
number again.

•You cannot store a number while the unit

is in the talk mode.

•Do not pause for over 60 seconds while

storing.

•If a power failure occurs, programmed

information may be erased. Reprogram if
necessary.

•If the last number dialed was more than

32 digits long, the number will not be
redialed correctly.

•The handset is too far from the base unit

or is engaged in an outside call.

•Charge the battery fully (6-A).

•Clean the charge contacts and charge

again (6-A).

•Install a new battery (6-B).
•This is normal.

•Call our customer call center at

1-800-211-PANA(7262).

•Panasonic’s e-mail address for customer

inquiries: 
consumerproducts@panasonic.com 
for customers in the USA or Puerto Rico
ONLY