Panasonic KX-TG2503NZF Manual De Usuario
Speed Dialler
Section 3
3
3-A Storing Phone Numbers in Memory
1
Press PROGRAM á.
•The TALK indicator flashes.
2
Enter a phone number up to 22 digits.
3
Press AUTO Ü.
4
Press a memory station number ((0) to (9)).
•A beep sounds.
•To store other numbers, repeat steps 1 through 4.
3-B Dialling a Stored Number
Press
(TALK)
\ AUTO
Ü
\ the memory station number (
(0)
to
(9)
).
If you misdial
Press PROGRAM á to end storing.
\
\ Start again from step 1.
To erase a stored number
Press PROGRAM á
\ AUTO Ü \
\ the memory station number ((0) to (9)) for the
phone number to be erased.
•A beep sounds.
phone number to be erased.
•A beep sounds.
•If a pause is required for dialling, press
(PAUSE)
where needed. Pressing
(PAUSE)
counts as one digit (5-C).
You can store up to 10 phone numbers in the handset. The dialling buttons ((0) to (9)) function as memory stations.
The TALK indicator light must be off before programming.
The TALK indicator light must be off before programming.
(PAUSE)
TALK Indicator
(TALK)
AUTO
Memory Station
Numbers
Numbers
PROGRAM
Special Features
5
5-A RECALL Button
Pressing (RECALL) allows you to use special features of your host PBX such as call transfer or accessing a
special telephone services (optional), such as call waiting.
special telephone services (optional), such as call waiting.
Selecting the recall time
The recall time depends on your telephone exchange or host PBX. You can select the following recall times:
“90, 100, 110, 250, 300, 400, 600 or 700 msec (milliseconds)”, using the handset near the base unit.
KX-TG2503ALF comes from the factory set to “100 msec”. KX-TG2503NZF comes from the factory set to
“600 msec”.
The TALK indicator light must be off before programming.
“90, 100, 110, 250, 300, 400, 600 or 700 msec (milliseconds)”, using the handset near the base unit.
KX-TG2503ALF comes from the factory set to “100 msec”. KX-TG2503NZF comes from the factory set to
“600 msec”.
The TALK indicator light must be off before programming.
Press PROGRAM á
AUTO Ü
(RECALL).
•If 3 beeps sound after programming, a wrong key was pressed. Start again from the beginning.
•Users in Australia can access Telstra’s “EASY CALL” service by having the recall time set at 100 msec, and
then follow Telstra’s “EASY CALL” instructions to operate this service.
•If you are connected via a PBX, a longer or shorter recall time may be necessary to use PBX functions
(transferring a call etc.). Consult your PBX supplier for the correct setting.
•When you receive a second call during a conversation, you will hear a signal tone following the call waiting tone
and the conversation will be interrupted for approximately a second. The tones are generated from the
telephone company. This is not fault of the product as these events are normal.
telephone company. This is not fault of the product as these events are normal.
•If a power failure occurs, the setting will return to the factory preset. Reprogram if necessary.
1 : 90 msec
2 : 100 msec
3 : 110 msec
4 : 250 msec
5 : 300 msec
6 : 400 msec
7 : 600 msec
8 : 700 msec
1
8
Dialling button ( to )
For Call Waiting Service Users in New Zealand
Adjust the recall time to 600 msec for use with Telecom’s Call Waiting Service. Press (RECALL) if you hear a
call-waiting tone while talking.
•The first call is put on hold and you can answer the second call.
call-waiting tone while talking.
•The first call is put on hold and you can answer the second call.
•To return to the first caller, press (RECALL) again.
(PAUSE)
AUTO
PROGRAM
,
(RECALL)
(TALK)
(HANDSETÒLOCATOR)
Button
Button
IN USE/CHARGE
Indicator
Indicator