Panasonic KX-TG2503NZF Manual De Usuario
Things You Should Know
Section 6
6-E Before Requesting Help
Problem
The unit does not work.
An alarm tone sounds.
Static, sound cuts in/out,
fades. Interference from
other electrical units.
fades. Interference from
other electrical units.
The unit does not ring.
Remedy
•Check the settings (1-C).
•Charge the battery fully (6-A).
•Clean the charge contacts and charge
again (6-A).
•Install the battery properly (6-B).
•Place the handset on the base unit and
unplug the AC adaptor to reset. Plug in,
and try again.
and try again.
•Re-install the battery and place the
handset on the base unit. Try again.
•KX-TG2503ALF/KX-TG2503NZF are not
designed to be used with rotary (pulse
dialling) services.
dialling) services.
•You are too far from the base unit. Move
closer and try again.
•Place the handset on the base unit and try
again.
•Make sure the AC adaptor is connected to
the base unit.
•Raise the base unit antennas.
•Locate the handset and the base unit
•Locate the handset and the base unit
away from other electrical appliances
(6-C).
(6-C).
•Move closer to the base unit.
•Raise the base unit antennas.
•Press
(CH)
to select a clearer channel.
•The ringer volume is set to OFF. Press
Ñ
or
Ö
while the TALK indicator light is off
(2-B).
Problem
While storing a phone
number, the unit starts to
ring.
number, the unit starts to
ring.
You cannot store a
phone number in
memory.
phone number in
memory.
Previously programmed
information is erased.
information is erased.
You cannot redial by
pressing
pressing
(REDIAL)
.
(HANDSET!LOCATOR)
does
not function.
The RECHARGE
indicator flashes or the
unit beeps intermittently.
indicator flashes or the
unit beeps intermittently.
You charged the battery
fully, but the RECHARGE
indicator flashes.
fully, but the RECHARGE
indicator flashes.
The IN USE/CHARGE
indicator light does not
go out while charging.
indicator light does not
go out while charging.
Remedy
•To answer the call, press
(TALK)
. The
program will be cancelled. Store the
number again.
number again.
•You cannot store a number while the unit
is in the talk mode.
•Do not pause for over 60 seconds while
storing.
•If a power failure occurs, programmed
information may be erased. Reprograme if
necessary.
necessary.
•If the last number dialled was more than
32 digits long, the number will not be
redialled correctly.
redialled correctly.
•The handset is too far from the base unit
or is engaged in an outside call.
•Charge the battery fully (6-A).
•Clean the charge contacts and charge
again (6-A).
•Install a new battery (6-B).
•This is normal.
•This is normal.
6-F Wall Mounting
1
Adjust the angle of the cradle:
#Slide the lock switch
to “RELEASE”.
$Rotate the cradle 90°
until it faces straight
up.
up.
%Slide the lock switch
to “LOCK” with the
cradle facing straight
up.
cradle facing straight
up.
2
Connect the AC adaptor.
3
#Tuck the telephone line
cord inside the wall
mounting adaptor.
mounting adaptor.
$Connect the telephone
line cord to the unit.
%Install the adaptor by
pushing it in the
direction of the arrow.
direction of the arrow.
•The word “UP” should
face upward.
4
Install screws using
the wall template.
Connect the
telephone line
cord. Mount the
unit, then slide
down.
the wall template.
Connect the
telephone line
cord. Mount the
unit, then slide
down.
•Raise the antennas.
1
3
Back Side
Back Side
2
To Power
Outlet
Outlet
2
3
1
Screws
8.3 cm
For Australia
To Telephone Plug
connected to Socket
OR
For New Zealand
To Single-Line
Telephone Jack
To Telephone Plug
connected to Socket
OR
For New Zealand
To Single-Line
Telephone Jack
This unit can be mounted on a wall.
8.3 cm
Wall Template