Panasonic kx-tg1805al Manual De Usuario
Multi-unit Operation
31
Operating additional units
Additional handsets
Up to 6 handsets can be registered to a
single base unit. Additional handsets will
give you the freedom to, for example, have
an intercom call with another handset while
a third handset is on an outside call. See
page 4 for information on ordering additional
handsets.
Important:
single base unit. Additional handsets will
give you the freedom to, for example, have
an intercom call with another handset while
a third handset is on an outside call. See
page 4 for information on ordering additional
handsets.
Important:
L
The additional handset model
recommended for use with this unit is
noted on page 4. If other model handset is
used, certain operations (handset
settings, base unit settings, etc.) may not
be available.
recommended for use with this unit is
noted on page 4. If other model handset is
used, certain operations (handset
settings, base unit settings, etc.) may not
be available.
L
The included handset can be registered to
only 1 base unit. You can use additional
handsets with this base unit, but you
cannot use the included handset with
another base unit unless you first cancel
the base unit from the included handset’s
memory.
only 1 base unit. You can use additional
handsets with this base unit, but you
cannot use the included handset with
another base unit unless you first cancel
the base unit from the included handset’s
memory.
Registering a handset to a
base unit
base unit
To register an additional handset to a
base unit (easy registration)
The included handset and base unit are
preregistered. After purchasing an
additional handset, register it to the base
unit. Ensure that the additional handset is
switched on. If it is not on, press and hold
{ih}
base unit (easy registration)
The included handset and base unit are
preregistered. After purchasing an
additional handset, register it to the base
unit. Ensure that the additional handset is
switched on. If it is not on, press and hold
{ih}
for few seconds to turn the handset
on.
1
Lift the additional handset and press
{ih}
{ih}
to put the handset in standby
mode.
2
Press and hold {x} on the base unit for
about 3 seconds, until the registration
tone sounds.
about 3 seconds, until the registration
tone sounds.
3
Place the additional handset on the
base unit. The registration tone
continues to sound. With the handset
still on the base unit, wait until a
confirmation tone sounds and w stops
flashing.
base unit. The registration tone
continues to sound. With the handset
still on the base unit, wait until a
confirmation tone sounds and w stops
flashing.
Note:
L
If an error tone sounds, or if w is still
flashing, register the handset manually
(manual registration; page 31).
flashing, register the handset manually
(manual registration; page 31).
L
L
Charge the batteries of your additional
handset for about 7 hours before initial
use.
handset for about 7 hours before initial
use.
Manual registration
You can register a handset to a base unit
manually using the following method.
You can register a handset to a base unit
manually using the following method.
1
Press {j/OK}.
2
Select “Handset Setup”, then press
{>}
{>}
.
3
Select “Registration”, then press
{>}
{>}
2 times.
L
If “Memory Full” is displayed, the
handset is already registered to a
base unit. You can cancel the base
unit from the handset’s memory if
necessary (page 32).
handset is already registered to a
base unit. You can cancel the base
unit from the handset’s memory if
necessary (page 32).
4
Press and hold {x} on the base unit for
about 3 seconds, until the registration
tone sounds.
about 3 seconds, until the registration
tone sounds.
L
If all registered handsets start ringing,
press {x} to stop, then repeat this
step.
press {x} to stop, then repeat this
step.
L
After pressing {x}, the rest of this
procedure must be completed within 1
minute.
procedure must be completed within 1
minute.
TG1805AL(e-e).book Page 31 Thursday, March 17, 2005 9:37 AM