Manual De UsuarioTabla de contenidosNotices9Welcome9Safety Notices9Safety Inspection9Remove AC Power10External Machine Check10Safety Label Check10Fusing Requirements11Environmental Notices and Statements11Product Recycling11Lithium Battery11Laser Safety11General Restrictions12Usage Restrictions12Regulatory Notices12Electronic Emission Statements12Federal Communications Commission (FCC) Statement12Industry Canada Compliance Statement13European Community Compliance Statement13VCCI Notice (Japan Only)14BSMI Notice14EN 55022 Compliance (Czech Republic Only)14CE Notice15Documentation16Introduction17Overview17Configuration Support18Address Mapping18Interface Protocol Awareness18Hardware Product Description and Features19Fibre Channel Interfaces19Ultra2 SCSI I/O Interfaces20SCSI Command Support21Ethernet21Service Port21LED Indicators22FC 1-222SCSI 1-423PWR23RDY23ERR23Supported Platforms23Supported Devices24Operating Specifications24Operating Environment24Power Consumption25Power Requirements25Install the SNC 510027Pre-installation Procedure27Installation Procedure28Host Utility Software31Post-Installation32Other Installation Issues32Attaching SCSI Devices32Maximum Number of LUNs32Transfer Rates: Ultra, Fast, and Asynchronous33Wide and Narrow SCSI Buses33Table of SCSI Terminology and Limitations34SCSI Bus Termination35Problems on the SCSI Bus35Missing terminator at the end of a SCSI bus36Excessive termination36Multiple devices at the same ID36Target device set to initiator’s ID36Bent pins in a SCSI connector36Improper device type36Improper terminator type36Inadequate cables37Mixed cable types37Unshielded cables37Fuses37Host Bus Adapter Setup37Installing the SAN Explorer38Installing the Host Registration Service38Power-Up and Boot Sequence Guidelines38Maintenance Action Plans41Event Codes and Actions42Check Event Log42Action Reference Table49Event Viewing Levels50Start MAP50Event Code or Obvious Symptom50Visually Inspect LEDs51Check for Problems on Attached Devices52Check Host Versions52Check SNC 5100 Product Versions52ADIC Management Console version52Firmware version53Hardware version53Quick Component Check54Perform Health Check54Check the Host Event Log55Database Full MAP55Device Access MAP56Check Fibre Channel Port Status57Check SCSI Channel Devices57Check Channel Zoning Settings58SCSI Channel MAP58Get SCSI Information for the SNC 510058Check Attached SCSI Devices from the Service Port59Compare Listed versus Physical Devices60Compare Listed versus Supported Devices60Check SCSI Bus Termination61Check for Multiple SCSI IDs62Improper Device Type63Examine SCSI Cables64Examine SCSI Connectors65SCSI Health Check65SCSI Loop Back Test66Testing SCSI Cables67Isolating SCSI devices67Restore SCSI Setup68Fibre Channel MAP69Verify Fibre Channel Connections69Test GBIC70Examine Cables71Fibre Channel Loop Back Test71Testing Fibre Channel Optical Cable72Replace Fibre Channel Cable73Replace Fibre Channel Device73MAP for the SNC 510074Observe Operational LED Behavior74Temperature MAP74Notification of Problems in Temperature Subsystem75Temperature Warnings or Alarms Received75Fan Speed is in Warning or Alarm Range76Power MAP76Ethernet MAP77Service Port MAP83Check the RS-232 Cable84Check Connection with Boot Messages84Virtual Private SAN®Scalar Firewall Manager Settings MAP85Check Scalar Firewall Manager Access Settings85Verify Host Access to Devices86Removal and Replacement Procedures89Handling Electrostatic Discharge-Sensitive Parts89Removing and Replacing the GBIC90Removing the GBIC90Replacing the GBIC90Before Removing or Replacing the Unit90Removing and Replacing the Unit91Removing the SNC 510091Replacing the SNC 510092Final Diagnostic Tests92Final Test Preparation92Fibre Channel Tests93Test Fibre Channel Port 193Test Fibre Channel Port 293Test SCSI Port 1 and 294Test SCSI Port 3 and 494Ethernet Test94Network Setup for the SNC 510095Updating the SNC 510098Post-Repair Checklist99Connecting to the Service Port103Service Port Connections103Connecting the Service Terminal104Hardware Required104Initial Setup of HyperTerminal105Verifying the Connection105Updating Firmware and Configurations106Updating SNC 5100 Firmware106Saving a Configuration File107Loading a Configuration File107Zmodem Status Code Table108Setting the Time and Date109Setting the Real Time Clock109Adding a Host System Running Timeserver110Disabling the Timeserver Host111Synchronizing the Real Time Clock with a Timeserver112Service Port Command Reference113Managing the SNC 5100113Commands113Diagnostic Command Reference195Boot Modes195Entering Diagnostic Mode195Restoring Normal Mode196Special Procedures196Health Check196Manual Health Check196Event Log Dump197Retrieving the Code 43 Dump File197Boot Mode Commands199Diagnostic Commands199POST Error Codes205POST Boot Behavior205ROM Init205Initial POST206Simple Access Test206Bitwalk Test207Memory Size207Pattern Test207Address Test208Secondary POST208Identify and Execute bootrom208Start of Bootrom209POST Service Menu209A - Cold boot from [A]lternate bootrom210B - Cold [B]oot from primary bootrom210R - [R]eceive new boot image from serial port211V- full [V]ersion information211Error Displays211Startup Message Reference213Bootrom Messages213LIC Initialization Messages214Final Startup Messages215Glossary217Acronyms217Warranty and EULA219ADIC Limited Product Warranty219ADIC End User License Agreement221INDEX225Tamaño: 2 MBPáginas: 228Language: EnglishManuales abiertas