Viewsonic PJ260D Manuales de usuario

Tabla de contenidos

• Introduction

  7
  • Projector Features

    7
  • Notes on the AC Power Cord

    7
  • Package Contents

    8
• Projector with Lens Cap

  8
• AC Power Cord

  8
• VGA Cable (D-SUB to D-SUB)

  8
• Remote Control (IR)

  8
• AAA size batteries for remote control

  8
• CD-Wizard

  8
• Quick Start Guide

  8
• Projector Carrying Case

  8
  • Projector Overview

    9
• Using the Product

  11
  • Control Panel

    11
  • Connection Ports

    12
  • Remote Control

    13
  • Installing the Batteries

    14
    • 1. Open the battery cover in the direction shown.

      14
    • 2. Install batteries as indicated by the diagram inside the compartment.

      14
    • 3. Close the battery cover into position.

      14
  • Remote Control Operation

    15
• Installation

  16
  • Connecting the Projector

    16
  • Powering On/Off the Projector

    17
• Powering On the Projector:

  17
  • 1. Remove the projector lens cap.

    17
  • 2. Complete the AC power cord and peripheral signal cable(s) connections.

    17
  • 3. Press button to turn on the projector. The projector takes a minute or so to warm up.

    17
  • 4. Turn on your source (computer, notebook, DVD, etc.). The projector automatically detects your source.

    17
• Powering Off the Projector:

  17
  • 1. Press button to turn off the projector lamp. You will see a message "Power off? Press Power again" appear on the screen.

    17
  • 2. Press button again to confirm.

    17
  • 3. Disconnect the AC power cord from the electrical outlet and the projector.

    17
  • 4. Do not turn on the projector immediately following a power off procedure.

    17
  • Adjusting the Projector

    18
• Adjusting the Projector Height

  18
  • 1. To raise or lower the image, press the elevator button and raise or lower the front of the projector. Release the button to lock the adjustment.

    18
  • 2. To level the image on the screen, turn the tilt-adjustment foot to fine-tune the height.

    18
• Adjusting the Projector Zoom and Focus

  18
  • 1. Focus the image by rotating the focus ring. A still image is recommended for focusing.

    18
  • 2. Adjust the image by sliding the zoom ring.

    18
• Adjusting Projection Image Size

  19
  • Menu Operation

    20
    • 1. Press the MENU button to open the OSD menu.

      21
    • 2. When OSD is displayed, use p / q to select any feature in the main menu.

      21
    • 3. After selecting the desired main menu feature, press u to enter sub-menu for feature setting.

      21
    • 4. Adjust the settings with t / u.

      21
    • 5. Press the MENU button, the screen will return to the main menu.

      21
    • 6. To exit OSD, press the MENU button again. The OSD menu will close and the projector will automatically save the new settings.

      21
  • Maintenance

    24
    • Cleaning the Lens

      24
    • Cleaning the Projector Housing

      24
    • Replacing the Lamp

      25
      • 1. Turn off the projector.

        26
      • 2. Unplug the power cord.

        26
      • 3. Place a protective sheet (cloth) beneath the projector. Turn the projector over so you can access the lamp cover.

        26
      • 4. Loosen the screw in the lamp cover and remove the cover.

        26
      • 5. Remove the screws from the lamp module, raise the handle, and lift out the module.

        26
      • 6. Insert the new lamp module into the projector and tighten the screws.

        26
      • 7. Replace the lamp cover and tighten the screw.

        26
      • 8. Turn on the projector. If the lamp does not turn on after the warm-up period, try reinstalling the lamp.

        26
      • 9. Reset the lamp hour. Refer to the “Setting (Computer / Video Mode)” menu.

        26
  • Specifications

    27
  • Appendix

    28
    • LED Indicator Messages

      28
    • Compatibility Modes

      29
• Computer:

  29
• Video:

  29
  • Troubleshooting

    30
• Start-up problems

  30
• Image problems

  30