Star Trac 7080 Manuel D’Utilisation
Page 28
SPINNER
®
OWNER’S GUIDE
ADJUSTMENTS
C
C
HAIN
T
ENSION &
A
DJUSTMENT
The chain on your bike has been factory set and lubricated. It should not require adjustment initially. Over time, however, you may need to adjust the
tension.
CAUTION: Improper chain adjustment will cause premature wear and may void the warranty.
tension.
CAUTION: Improper chain adjustment will cause premature wear and may void the warranty.
To adjust chain on Spinner
®
V:
1. Using a 3mm Allen Wrench, remove the three screws supporting the
plastic chain guard shroud.
2. With an adjustable wrench, loosen the two nuts on both sides of the
flywheel (Figure 1 & 2).
3. Tighten the two bolts that go through the frame, moving the flywheel
forward by turning clockwise, until there is approximately 3/16” of slack
in the chain (Figure 1 & 2).
4. Re-tighten the two bolts on both sides of the flywheel and replace the
chain guard shroud.
NOTE: If the chain is too tight, typically the rider will feel a strong
vibration between 20 and 50 RPMs. If this happens, loosen the bolts 1/2”
turn until the vibration disappears, then tighten the lock nuts.
flywheel (Figure 1 & 2).
3. Tighten the two bolts that go through the frame, moving the flywheel
forward by turning clockwise, until there is approximately 3/16” of slack
in the chain (Figure 1 & 2).
4. Re-tighten the two bolts on both sides of the flywheel and replace the
chain guard shroud.
NOTE: If the chain is too tight, typically the rider will feel a strong
vibration between 20 and 50 RPMs. If this happens, loosen the bolts 1/2”
turn until the vibration disappears, then tighten the lock nuts.
Figure 1.
Chain guard side (View shows chain guard shroud
removed)
Figure 2.
Other side opposite of chain
To adjust chain on Spinner
®
Pro / Elite / NXT:
1. Using a 3mm Allen Wrench, remove the three screws supporting the
plastic chain guard shroud. (Figures 3 & 4)
2. Using a 16mm or 5/8” socket and socket wrench, loosen the axle nuts
on both sides of the flywheel.
plastic chain guard shroud. (Figures 3 & 4)
2. Using a 16mm or 5/8” socket and socket wrench, loosen the axle nuts
on both sides of the flywheel.
3. Using a 10mm open end wrench, loosen the lock nuts on the chain
adjustment screws.
4. To tighten the chain, turn the adjustment screw in a clockwise rotation
equally on both sides using the 10mm open end wrench. (Figure )
5. To loosen the chain, turn the adjustment screws on both sides counter-
clockwise using a 10mm open end wrench.
6. While adjusting the chain tension, work on both sides of the flywheel.
Adjust the angle of the flywheel so it is straight front to rear and evenly
spaced within the frame side to side. (Figure )
7. Align the chain so it runs straight on both of the sprockets.
8. Adjust the angle of the flywheel by adjusting the adjustment screws
on both sides of the flywheel. Test by slowly rotating the pedals.
adjustment screws.
4. To tighten the chain, turn the adjustment screw in a clockwise rotation
equally on both sides using the 10mm open end wrench. (Figure )
5. To loosen the chain, turn the adjustment screws on both sides counter-
clockwise using a 10mm open end wrench.
6. While adjusting the chain tension, work on both sides of the flywheel.
Adjust the angle of the flywheel so it is straight front to rear and evenly
spaced within the frame side to side. (Figure )
7. Align the chain so it runs straight on both of the sprockets.
8. Adjust the angle of the flywheel by adjusting the adjustment screws
on both sides of the flywheel. Test by slowly rotating the pedals.
Figure 3. Pro Figure 4. NXT
Figure 5A. Pro/Elite Figure 5B. Pro/Elite
Chain Guard Side Other Side of Chain
Guard
Chain Guard Side Other Side of Chain
Guard
Axle Nuts
Adjustment
Screws
Screws