Manualsbrain.com
  1. Manuels
  2. Marques
  3. Samsung
  4. SCX-6545N Series
  5. Manuel D’Utilisation

Samsung SCX-6545N Series Manuel D’Utilisation

Télécharger
Page de 190
109 _
Troubleshooting
Finisher error: [zzz]. 
Please turn off then 
on
There is a problem in 
the finisher unit.
Turn the machine off 
and reinstall the finisher 
again. Check that the 
finisher cable is 
connected properly. If 
the problem persists, 
please call for service.
Fuser error: [zzz]. 
Please turn off then 
on
There is a problem in 
the fuser unit working.
Turn the machine off 
and turn it on again. If 
the problem persists, 
please call for service.
Fuser unit is not 
installed correctly. 
Install it
The fuser unit is not 
installed or correctly.
Install the fuser unit. 
Call for service.
Imaging unit is 
empty. Replace it
The toner in the 
imaging unit has run 
out. 
Replace the imaging 
unit with a Samsung-
genuine toner cartridge. 
Imaging unit is not 
compatible. Check 
user’s guide
The imaging unit you 
have installed is not 
for your machine.
Install a Samsung-
genuine imaging unit, 
designed for your 
machine.
Imaging unit is not 
installed. Install it
The imaging unit is 
not installed, or the 
CRUM (Consumer 
Replaceable Unit 
Monitor) in the 
cartridge is not 
connected.
Install the imaging unit. 
If it is already installed, 
try to reinstall the 
imaging unit. 
If the problem persists, 
please call for service.
Imaging unit is 
worn. Replace with 
new one
The imaging unit is at 
the end of its life. 
When the imaging unit 
replacement message 
appears on the screen 
and if you select 
Continue
, this 
message displays. 
Replace a imaging unit 
with a Samsung-
genuine imaging unit. 
LSU error: [zzz]. 
Please turn off then 
on
There is a problem in 
the control of LSU 
unit.
Turn the machine off 
and turn it on again. If 
the problem persists, 
please call for service.
Motor does not 
operate: [zzz]. 
Please turn off then 
on
There is a problem in 
the control of motor 
unit.
Turn the machine off 
and turn it on again. If 
the problem persists, 
please call for service.
Original paper does 
not feed in scanner
The lead edge of the 
document failed to 
actuate the scan 
sensor within the 
correct time after 
actuating the 
registration sensor.
Open the DADF cover 
and remove jammed 
MESSAGE
MEANING
SUGGESTED 
SOLUTIONS
Original paper is too 
long for scanner. 
Check size
Oversized document 
or double-feeding of 
originals.
Open the DADF cover 
and remove the 
jammed original. (See 
Check the document 
size whether it is 
Original paper jam 
in front of scanner
The originals are 
jammed in DADF.
Open the DADF cover 
and remove the 
jammed original. (See 
Original paper jam 
in front of scanner 
duplex path
Paper has jammed 
during duplex printing 
in the DADF.
Clear the jam. (See 
Original paper jam 
inside of scanner
The lead edge of the 
document failed to 
actuate the gate 
sensor within the 
correct time after 
actuating the scan 
sensor.
When the machine is 
on, jammed paper is 
detected in the DADF.
Open the DADF cover 
and remove the 
jammed original. (See 
Original paper jam 
while reversing 
paper in scanner
The lead edge of the 
document failed to 
actuate the duplex 
sensor within the 
correct time when the 
document was fed the 
wrong way.
Lift up the document 
input tray and remove 
the jammed original. 
Paper jam at exit of 
finisher
Paper jammed in the 
stacker exit part.
Pull jammed paper 
from the stacker exit.
Paper Jam at the 
bottom of duplex 
path
Paper has jammed 
during duplex printing.
Clear the jam. (See "In 
Paper Jam at the top 
of duplex path
Paper Jam in exit 
area
Paper has jammed in 
the fuser area.
Clear the jam. (See "In 
Paper jam in front of 
finisher
Paper jammed in the 
stacker.
Open the stacker door 
and remove jammed 
paper by lowering 
guide 1a or 1b.
Paper jam inside 
finisher
MESSAGE
MEANING
SUGGESTED 
SOLUTIONS