Multiquip MC3P (B&S) Manuel D’Utilisation
PAGE 22 —MIX N' GO MIXER — OPERATION & PARTS MANUAL — REV. #5 (1/07/05)
MIX N' GO MIXER — INITIAL START-UP (ELECTRIC MOTOR)
CAUTION:
CAUTION:
CAUTION:
CAUTION:
CAUTION:
DO NOT attempt to operate the mixer until
the Safety, General Information and
the Safety, General Information and
Inspection sections have been read and
understood.
understood.
Initial Start-up Instructions (Electric Motor)
Starting
1. Before starting, make sure mixer is positioned on a secure
flat surface to prevent tipping.
2. Use an extension cord (see Table 5) of adequate current
carrying capacity, insert the electric motor's power plug into
one end of the extension cord.
one end of the extension cord.
3.
NEVER! use a worn or frayed extension cord.
4.
NEVER! operate mixer with V-belt cover removed.
5. Plug the other end of the extension cord into a 120 VAC
G.F.C.I. protected receptacle. Remember the power require-
ments for this electric motor is 120 VAC, 60 Hz. The use of
any other input voltage will severely damage the motor.
ments for this electric motor is 120 VAC, 60 Hz. The use of
any other input voltage will severely damage the motor.
DANGER
DANGER
DANGER
DANGER
DANGER
NEVER! touch the power cord (Figure 17)
with
with
wet hands or while standing in water
when it is connected to a power source. The
possibly exists of electrical shock
(electrocution) even death.
possibly exists of electrical shock
(electrocution) even death.
NEVER! spray
water directly on the electric motor.
POWER
CORD
(POWER ON)
WET
HANDS
Figure 17. Extension Cord (Wet Hands)
WARNING:
WARNING:
WARNING:
WARNING:
WARNING:
ALWAYS read the label on the electric motor
before applying power. The label will indicate the
proper power requirements for the motor.
Remember the use of any other input voltage will
severely damage the motor.
before applying power. The label will indicate the
proper power requirements for the motor.
Remember the use of any other input voltage will
severely damage the motor.
WARNING:
WARNING:
WARNING:
WARNING:
WARNING:
To prevent tripping (Figure 18) of both the mixer
and personnel, position the extension cord so that
it lays flat and is not curled underneath the mixer.
and personnel, position the extension cord so that
it lays flat and is not curled underneath the mixer.
Figure 18. Mixer (Tripping)
6. The drum should be rotating allowing the mixing process to
begin. Use a shovel (Figure 19) to place the cement mix
inside the drum, add water as required. Be careful to only
place the
inside the drum, add water as required. Be careful to only
place the
tip of the shovel inside the drum. Placing the shovel
all the way inside the drum will cause the shovel to strike the
blades. This condition will make the shovel rotate, and could
cause injury to personnel.
blades. This condition will make the shovel rotate, and could
cause injury to personnel.
Figure 19. Mixing Drum (Placing Cement Mix)
6. See Table 3 for mixing hints.
NEVER! place hands inside the
drum while the drum is rotating.
e
z
i
S
d
r
o
C
n
o
i
s
n
e
t
x
E
.
5
e
l
b
a
T
e
r
i
W
2
1
.
o
N
e
r
i
W
0
1
.
o
N
e
r
i
W
8
.
o
N
e
r
i
W
6
.
o
N
)
t
e
e
f
(
0
5
)
s
r
e
t
e
m
4
2
.
5
1
(
)
t
e
e
f
(
5
7
s
r
e
t
e
m
6
8
.
2
2
(
)
t
e
e
f
(
0
0
1
s
r
e
t
e
m
8
4
.
0
3
(
)
t
e
e
f
(
0
0
2
s
r
e
t
e
m
6
9
.
0
6
(