Freestyle Mariner Manuel D’Utilisation

To reduce carbon foot print, these

Freestyle instructions are printed with

soy inks on recycled paper.

ENGLISH

(CHIME) setting will blink. Press S1

button to toggle between ON and OFF

for the hourly chime setting.

10. When finished making all the settings,

press S3 button to confirm.

NOTE: The hourly chime setting will apply

to both HOME TIME mode and FOREIGN

TIME mode.

TO USE THE CHRONOGRAPH:

1. Press S2 button to select CHRONO-

GRAPH mode.

2. The chronograph will then be displayed

in its current state – stopped, running

or reset.

3. To resume a stopped counting, press

S1 button to resume from where it left

off.

4. To start a new counting, reset the

chronograph to zero first.

Press S1 button to stop counting, then

press S3 button to reset counter to

zero.

For the measurement of elapsed time:

In CHRONOGRAPH mode,

1. Press S1 button to start counting.

2. To stop counting, press S1 button once.

Press S1 button again to resume from

where it left off.

3. To reset to zero, press S1 button to stop

counting and then press S3 button.

For the measurement of split time:

In CHRONOGRAPH mode,

1, Press S1 button to start counting.

2, While the chronograph is running,

press S3 button once to register a lap.

The split time of the registered lap will

be displayed. The chronograph is still

running in the background.

3. To display the current elapsed time,

press S3 button again.

4. Repeat the last step until all the laps

have been registered.

5. To reset to zero, press S1 button to stop

counting and then press S3 button.

For the measurement of two finishes:

In CHRONOGRAPH mode,

1. Press S1 button to start counting.

2. While the chronograph is running,

press S3 button to register and display

the time of the first runner. The

chronograph is still running in the

background.

3. Press S1 button to stop and register the

time of the second runner.

4. Press S3 button to display the time of

the second runner.

5. To reset to zero, press S3 button again.

NOTE: The chronograph can count up to

a maximum of 23 hours, 59 minutes and

59.99 seconds.

NOTE: You can leave the chronograph

running while switching over to other

operating modes.

TO SET THE TIMER:

1. Press S2 button to select TIMER mode.

2. Press S3 button, the message “HOLD

TO SET” will be displayed for approxi-

mately 3 seconds and the hour digits

will blink.

3. Press S1 button to alter the timer set-

ting among 60, 55, 50, 45, 40, 35, 30, 25,

20, 15, 14, 13, 12, 11, 10, 9, 8, 7, 6, 5, 4,

3, 2, and 1 minutes.

4. Press S2 button, the “Action-at-End”

setting will blink. Press S1 button to

select among STOP AT END (STOP),

REPEAT AT END (REPEAT) and COUNT

UP AT END (UP).

5. When finished making all the settings,

press S3 button to confirm.

NOTE: Definitions of Action-at-End setting

option:

a) STOP AT END – the timer will stop

when the countdown reaches zero.

b) REPEAT AT END – the timer will repeat

the countdown when the countdown

reaches zero.

c) COUNT UP AT END – the timer will

count up to a maximum of 23 hours

59 minutes and 59 seconds when the

countdown reaches zero.

TO USE THE TIMER:

1. Press S3 button to select TIMER mode.

2. The timer will then be displayed in its

current state – stopped, running, or

reset.

3. To resume a stopped counting, press

S1 button to resume from where it left

off.

4. To start a new counting, reload the

timer first.

Press S1 button to stop counting, then

press S3 button to reload the timer.

5. When reaching zero in a countdown, a

tune will be emitted. To stop the tune,

press any button.

NOTE: You can leave the timer running

while switching to other operating modes.

TO SET THE ALARM TIME:

1. Press S2 button to select ALARM

mode.

2. Press and hold S3 button, the message

“HOLD TO SET” will be displayed and

the hour digits will blink. Press S1 but-

ton to set the hour digits. Holding down

the button will speed up the process.

3. Press S2 button, the minute digits will

blink. Press S1 button to set the minute

digits. Holding down the button will

speed up the process.

4. When finished making all the settings,

press S3 button to confirm.

NOTE: The alarm will automatically be

activated after being set.

TO TURN ON/OFF THE ALARM:

In ALARM mode, press S1 button to toggle

between ON and OFF of the alarm. When

the alarm is ON, the alarm indicator

will appear.

WHEN AN ALARM GOES OFF:

A 20-second alarm tune will be emitted

at the designated time when the alarm

is activated. To stop the tune, press any

button.

TO USE THE BACKLIGHT:

Press S4 button to turn on the backlight

for 3 seconds.

FS_119 MARINER_A

G7502-F

S-INST-PK

G-R00

S1. Start/stop button

S2. Mode button

S3. Set/reset button

S4. Light button

SPECIAL FEATURE:

This Freestyle product features unique

Hydro Pushers®: these pushers can be

pressed under water to a dynamic water

pressure (not water depth) of 3 ATM.

DISPLAY MODES:

The watch has four display modes: HOME

TIME (T1)/FOREIGN TIME (T2), CHORONO-

GRAPH (CHRONO), TIMER and ALARM.

To change from one display mode to

another, press S2 button once.

Note: In any setting mode, if there is no

button pressed for a few minutes, the

watch will automatically save the entered

data and exit the setting procedure.

HOME AND FOREIGN TIME DISPLAY:

To display FOREIGN TIME mode, press

and hold S1 button when HOME TIME

mode is displayed. The mode descrip-

tion (T2) will be displayed and blink for

approximately 5 seconds before switching

to FOREIGN TIME mode. To change back

to HOME TIME mode, press and hold S1

button again.

TO SET THE TIME AND CALENDAR:

1. Press S2 button to select HOME TIME

(T1)/FOREIGN TIME (T2) mode.

2. Press and hold S3 button, the message

“HOLD TO SET” will be displayed for

approximately 3 seconds and the time

zone setting will blink.

3. Press S1 button to toggle between

HOME TIME (T1) and FOREIGN TIME

(T2) to set.

4. Press S2 button, the hour digits will

blink. Press S1 button to set the hour

digits. Holding down the button will

speed up the process.

5. Press S2 button, the minute digits will

blink. Press S1 button to set the minute

digits. Holding down the button will

speed up the process.

6. Press S2 button, the second digits

will blink. Press S1 button to reset the

second digits to zero.

7. Follow the same pattern to set the year,

month and date.

8. Press S2 button, the hour format set-

ting will blink. Press S1 button to toggle

between 12-hour and 24-hour format.

The A.M. or P.M. indicator may be dis-

played to indicate the time period 12:00

A.M. – 11:59 A.M. or 12:00 P.M. – 11:59

P.M. respectively in 12-hour format.

9. Press S2 button, the hourly chime

MARINER