Freestyle Stride Manuel D’Utilisation

ENGLISH

S1- Start/lap Button

S2- Stop/reset Button

S3- Mode/next Button

S4- Light Button

S5- Lap Button

SPECIAL FEATURE:

This Freestyle product features unique

Hydro Pushers®: these pushers can be

pressed under water to a dynamic water

pressure (not water depth) of 3 ATM.

DISPLAY MODES:

The watch has six display modes: NOR-

MAL TIME, CHRONOGRAPH, RECALL,

TIMER, HEAT TIMER and ALARM.

To change from one display mode to

another, press S3 button once.

TO SET THE TIME AND CALENDAR:

1. Press S3 button to select NORMAL

TIME mode.

2. Press and hold S1 button to toggle

between Time Zone 1 (T1) and Time

Zone 2 (T2)

3. Press and hold S2 button, the

message “HOLD TO SET” will be dis-

played for approximately 2 seconds

and the Time Zone setting will blink.

4. Press S1 button to select Time Zone

1 (TIME 1) or Time Zone 2 (TIME 2) to

set.

5. Press S3 button, the hour digits will

blink.

6. Press S1 button to increase the hour

digits by one unit. Holding down the

button will speed up the process.

7. Press S3 button, the minute digits

will blink.

8. Press S1 button to set the minute

digits.

9. Press S3 button, the second digits

will blink.

10. Press S1 button to reset the second

digits to zero.

11. Press S3 button, the month digits

will blink.

12. Press S1 button to set the month

digits.

13. Press S3 button, the date digits will

blink.

14. Press S1 button to set the date

digits.

15. Press S3 button, the year digits will

blink.

16. Press S1 button to set the year

digits.

17. Press S3 button, the time format

setting will blink.

18. Press S1 button to toggle between

12-hour (12HR) format and 24-hour

(24HR) format.

19. Press S3 button, the date setting

format will blink.

20. Press S1 button to toggle between

month-date (MM-DD) format and

date-month (DD-MM) format.

21. Press S3 button, the hourly chime

(CHIME) setting will blink.

22. Press S1 button to toggle between

ON and OFF of the hourly chime

setting.

23. Press S3 button once, the button

beep (BEEP) setting will blink.

24. Press S1 button to toggle between

ON and OFF of the button beep set-

ting.

25. When finished making all the set-

tings, press S2 button to confirm.

NOTE: In 12-hour format, the hour

digits are identified by “PM” for 12:00

P.M.-11:59 P.M.

NOTE: The day (of the week) is automati-

cally calculated.

NOTE: The year digits range from 2008

to 2099.

TO USE THE CHRONOGRAPH:

1. Press S3 button to select CHRONO-

GRAPH mode.

2. The maximum number of laps that

can be stored in a new workout will

be displayed. If the lap memory is full,

the message “FULL” will be displayed

and a tune will be emitted.

3. The chronograph will then be dis-

played in its current state- stopped,

running, or reset.

4. To resume a stopped counting, press

S1 button to resume from where it

left off.

5. To start a new counting, reset the

chronograph to zero first. Press and

hold S2 button, the message “HOLD

TO CLR” will be displayed for approxi-

mately 2 seconds and the counter will

be reset to zero.

For changing the chronograph display

format:

In CHRONOGRAPH mode,

1. Make sure the chronograph is in the

reset state and there is no previous

lap record.

2. Press S4 button to toggle between

LAP format or SPL format.

3. If LAP format is selected, the lap time

(individual lap time) will be displayed.

If SPL format is selected, the split

time (cumulative lap time) will be

displayed.

For the measurement of elapsed time:

In CHRONOGRAPH mode,

1. Press S1 button to start counting.

2. To stop counting, press S2 button.

Press S1 button to resume from

where it left off.

3. To reset to zero, press S2 button to

stop counting, then press and hold S2

button, the message “HOLD TO CLR”

will be displayed for approximately 2

seconds and the counter will be reset

to zero.

For the measurement of split time:

In CHRONOGRAPH mode,

1. Press S1 button to start counting.

2. While the chronograph is running,

press S1/S5 button to register a lap.

3. Depends on the chronograph display

format chosen, the individual lap time

of the previous lap (if LAP format is

chosen) or the cumulative lap time

(if SPL format is chosen) will be

displayed. The lap number of the

previous lap will be blinking at the top

line of the display.

After 10 seconds, the current elapsed

time and the current lap number will

be displayed.

4. Repeat the last step until all the laps

have been registered.

5. To stop counting, press S2 button.

The total accumulated lap time will

be displayed.

6. To reset to zero, press and hold S2

button, the message “HOLD TO CLR”

will be displayed for approximately 2

seconds and the counter will be reset

to zero.

For using the 5-second countdown start:

In CHRONOGRAPH mode,

1. Make sure the chronograph is in the

reset state and there is no previous

lap record.

2. Press and hold S2 button, the number

“5” will flash for approximately 2

seconds, and then the 5-second

countdown start will be activated.

3. Press S1 button to initiate the 5-sec-

ond count down.

4. After 5 seconds (count down to zero),

a long beep will be emitted and the

chronograph will be initiated.

NOTE: The chronograph can count

up to a maximum time of 99:59:59:99

(99hours, 59 minutes, 59:99 seconds).

If the chronograph has reached the

maximum time as specified, press and

hold S2 button to reset the chronograph

to zero.

NOTE: You can leave the chronograph

running while switching over to other

operating modes. In NORMAL TIME

mode, the chronograph indicator will

appear as a reminder.

For saving the lap record:

In CHRONOGRAPH mode,

1. Upon finishing a counting, press and

hold S4 button, the message “HOLD

TO SAVE” will be displayed for ap-

proximately 2 seconds.

2. If there is sufficient memory, the

lap record will be stored and the

remaining available lap memory will

be displayed.

If there is insufficient memory, the

lap record will be stored along with as

many of the oldest splits as possible

and the message “FULL” will be

displayed.

TO USE THE RECALL MODE:

1. Press S3 button to select RECALL

mode.

2. If there is lap record stored, the data

stamp (showing the day of the week,

date and month) of a stored data will

blink at the upper line of the display.

If there is no lap record stored, the

message “no DATA” will be displayed.

3. Press S1 button to cycle the date

stamp(s) of the corresponding lap

record(s). This has no effect if there is

no lap record stored.

4. When the desired lap record is dis-

played, press S2 button to select.

5. Press S1 button to cycle the details of

the selected lap record in the order of:

STRIDE