Boss Audio Systems mr1315bua Manuel D’Utilisation
Page 2
Page 9
1) TA SEEK/TA ALARM:
TA SEEK mode: when newly tuned station does not receive TP information for 5
seconds, the radio retunes to next station which has a different PI to the last station,
but has the TP information.
When TP information gets lost at the current station for retune time which is set by
RETUNE SHORT(90 seconds) or RETUNE LONG(150 seconds), the radio starts to
retune to next same PI station. When same PI station does not receive in 1 cyclic
search, the radio retunes to next station with TP information.
TA ALARM mode: when this mode is selected, any automatic retune mode is not
activated. Only double beep sound(ALARM) will be heard.
seconds, the radio retunes to next station which has a different PI to the last station,
but has the TP information.
When TP information gets lost at the current station for retune time which is set by
RETUNE SHORT(90 seconds) or RETUNE LONG(150 seconds), the radio starts to
retune to next same PI station. When same PI station does not receive in 1 cyclic
search, the radio retunes to next station with TP information.
TA ALARM mode: when this mode is selected, any automatic retune mode is not
activated. Only double beep sound(ALARM) will be heard.
When TP information gets lost at the current station for retune time, the beep sound
will be heard.
When newly tuned station has no RDS signal, PI SEEK is suppressed .
will be heard.
When newly tuned station has no RDS signal, PI SEEK is suppressed .
2) PI SOUND/ PI MUTE:
PI SOUND mode: if a car cruises between buildings that could cause reflecting
signals, a phenomenon may occur, due to different PI codes being received from the
same AF source. when different PI sounds (DIP) are heard occassionally, this will
happen for less than 1 second.
PI MUTE mode: under above same situation, a mute sound will be heard for less
than1second.
signals, a phenomenon may occur, due to different PI codes being received from the
same AF source. when different PI sounds (DIP) are heard occassionally, this will
happen for less than 1 second.
PI MUTE mode: under above same situation, a mute sound will be heard for less
than1second.
3) RETUNE L / RETUNE S:
The initial time of automatic TA search or PI SEARCH mode is selected.
When PI information is not received for retune interval , the radio starts to retune to
next same PI station.
When same PI station does not receive 1 cyclic search, the radio goes to last station
and waits for 4-5 minutes until PI code is received.
RETUNE L mode: selected as 150 seconds.
RETUNE S mode: selected as 90 seconds.
When PI information is not received for retune interval , the radio starts to retune to
next same PI station.
When same PI station does not receive 1 cyclic search, the radio goes to last station
and waits for 4-5 minutes until PI code is received.
RETUNE L mode: selected as 150 seconds.
RETUNE S mode: selected as 90 seconds.
4) MASK DPI/MASK ALL:
MASK DPI mode: masks only the AF which has different PI.
MASK ALL mode: masks the AF which has different PI and NO RDS signal with high
field strength.
MASK ALL mode: masks the AF which has different PI and NO RDS signal with high
field strength.
5)BEEP ON/BEEP OFF
BEEP ON mode: The beep is generated when any key is pressed.
BEEP OFF mode: The beep sound is disabled.
BEEP OFF mode: The beep sound is disabled.
6) VOL LAST/VOL DEFA
VOL LAST: The radio switches on at the actual volume it had when it was last
switched off.
VOL DEFA: After pressing SEL button, AVOL will be displayed. Then you can
pre-select a constant switch-on volume by using the VOL knob.
7)CLK ON/OFF
CLK ON: Clock will always show on the display when power off.
CLK OFF: Clock will disappear on the display when power off.
CLK OFF: Clock will disappear on the display when power off.
Press it to select RADIO, CARD(after inserting MMC/SD card), USB(after inserting
USB stick) ,IPOD (after connect IPOD cable) and AUX mode.
USB stick) ,IPOD (after connect IPOD cable) and AUX mode.
When newly tuned station does not have TP information for 5 seconds, beeps are
sound ed.
sound ed.
5. LCD Display
6. MODE BUTTON
Specifications
NOTE:
Specifications and design are subject to modification, without notice,
due to improvements in technology.
due to improvements in technology.
Supply voltage
: 12V DC(11V-15V)
Current consumption
: Less than 10A
Audio Signal Output
: 2ch line out
Characteristics
: (1)
Frequency Response: 20Hz-20KHz
S/N Ratio:
50 dB(JIS)
(2)
(Europe)
(U.S.A.)
FM
FM
Frequency Coverage:
IF
IF
10.7Mhz
10.7Mhz
Sensitivity (S/N = 30dB) : 20dBu
20dBu
AM
AM
Frequency Coverage:
IF
IF
450
450
Sensitivity (S/N = 20dB) : 45dBu
45dBu
87.5 to 108Mhz
87.5 to 107.9Mhz
522 to 1620Khz
530 to 1710Khz
Khz
Khz
PDF created with FinePrint pdfFactory Pro trial version