Tyco Electronics M7300 Series Manuel D’Utilisation
MM-014716-001
74
9.15.1 Status Operation
Status operation permits the transmission of a pre-programmed status condition to the EDACS site.
To send a status condition, press the STS button (keylight comes on) then press one of the number
buttons (0-9) to select the pre-programmed status. If no status has been programmed for the selected
number button, the radio will display NO ENTRY and the radio will sound a low tone. A valid selection
will permit the status text to appear in the display for a pre-programmed time. After the time-out expires
or the MENU button has been pressed (the MENU button will override the time-out period), the status is
selected and will be transmitted to the site or stored in the radio memory where it can be polled by the site
at a future time. If the site receives the status properly, when transmitted or polled by the site, a high-
pitched tone sounds and the keylight associated with that status will remain lit. If the site does not receive
the status properly, a low-pitched tone sounds and the keylight associated with the status will blink.
buttons (0-9) to select the pre-programmed status. If no status has been programmed for the selected
number button, the radio will display NO ENTRY and the radio will sound a low tone. A valid selection
will permit the status text to appear in the display for a pre-programmed time. After the time-out expires
or the MENU button has been pressed (the MENU button will override the time-out period), the status is
selected and will be transmitted to the site or stored in the radio memory where it can be polled by the site
at a future time. If the site receives the status properly, when transmitted or polled by the site, a high-
pitched tone sounds and the keylight associated with that status will remain lit. If the site does not receive
the status properly, a low-pitched tone sounds and the keylight associated with the status will blink.
If an incorrect status was selected or the incorrect number button was pressed, the status can be changed
during the pre-programmed time-out period by pressing another number button. The status selection can
also be cancelled by pressing the CLR button prior to the time-out period.
during the pre-programmed time-out period by pressing another number button. The status selection can
also be cancelled by pressing the CLR button prior to the time-out period.
To view the currently selected status after it has been transmitted, press the STS button. If the status was
not sent successfully to the site, the text associated with the status will flash in the display.
not sent successfully to the site, the text associated with the status will flash in the display.
The radio can also be pre-programmed to redesignate the keypad buttons for ST0 thru ST9 to send status
condition. In this configuration the radio status operation will operate as previously described except the
STS button is not required. The keylight associated with ST0 thru ST9 will indicate which status is
selected.
condition. In this configuration the radio status operation will operate as previously described except the
STS button is not required. The keylight associated with ST0 thru ST9 will indicate which status is
selected.
9.15.2 Message Operation
Message operation permits the transmission of a pre-programmed message text to an EDACS site.
To send a message, press the MSG button (keylight comes on) then press one of the number buttons (0-9)
to select the pre-programmed message text. If no message text has been programmed for the selected
number button, the radio will display NO ENTRY and a low-pitched tone sounds. A valid selection will
permit the message text to appear in the display for a pre-programmed time. After the time-out expires or
the MENU button has been pressed (the MENU button will override the time-out period), the message
text is selected and will be transmitted to the site. If the site receives the message properly when
transmitted, a high pitched tone sounds and the MSG keylight remains lit. If the site does not receive the
message properly, a low-pitched tone sounds and the MSG keylight will blink.
to select the pre-programmed message text. If no message text has been programmed for the selected
number button, the radio will display NO ENTRY and a low-pitched tone sounds. A valid selection will
permit the message text to appear in the display for a pre-programmed time. After the time-out expires or
the MENU button has been pressed (the MENU button will override the time-out period), the message
text is selected and will be transmitted to the site. If the site receives the message properly when
transmitted, a high pitched tone sounds and the MSG keylight remains lit. If the site does not receive the
message properly, a low-pitched tone sounds and the MSG keylight will blink.
If an incorrect message text was selected or the incorrect number button was pressed, the message text
can be changed during the pre-programmed time-out period by pressing another number button. The
message text selection can also be cancelled by pressing the CLR button prior to the time-out period.
can be changed during the pre-programmed time-out period by pressing another number button. The
message text selection can also be cancelled by pressing the CLR button prior to the time-out period.
To view the currently selected message text after it has been transmitted, press the MSG button and then
the CLR button prior to the time-out period. If the message text was not sent successfully to the site, the
text associated with the message will flash in the display.
the CLR button prior to the time-out period. If the message text was not sent successfully to the site, the
text associated with the message will flash in the display.
9.16 EDACS CONVENTIONAL P1 SCAN
This feature permits the radio user to scan a pre-programmed conventional system and channel as a
Priority 1 (P1) channel while the radio is selected for EDACS trunked system. If activity is detected on
the conventional P1 channel, the radio will unmute and remain on this conventional channel for the
programmable hang time.
Priority 1 (P1) channel while the radio is selected for EDACS trunked system. If activity is detected on
the conventional P1 channel, the radio will unmute and remain on this conventional channel for the
programmable hang time.
The radio must be pre-programmed to designate a button for scan ON/OFF operation.