iHome ZN9 Manuel D’Utilisation
ZN9 IB_0521_b.fh10 6/11/08 1:24 PM Page 6
Install/Replace Backup Battery
The ZN9 uses a backup battery system to provide continuous alarm operation and clock settings
in the event of a power failure. If the Battery Low Icon located on the right of the display is flashing,
it is time to replace the backup batteries. Please make sure the AC adaptor is connected, otherwise
all settings may be lost during battery replacement.
The ZN9 uses a backup battery system to provide continuous alarm operation and clock settings
in the event of a power failure. If the Battery Low Icon located on the right of the display is flashing,
it is time to replace the backup batteries. Please make sure the AC adaptor is connected, otherwise
all settings may be lost during battery replacement.
Open the battery compartment cover located on the bottom of the unit. Insert 2 “AA” batteries
as indicated. We recommend the use of alkaline batteries for longer life.
as indicated. We recommend the use of alkaline batteries for longer life.
Batteries information:
•
•
Do not mix old and new batteries.
•
Do not mix alkaline, standard (carbon -zinc) or rechargeable (nickel-cadmium) batteries.
Replacing ZN9 Backup Batteries
4
Using the ZN9
Radio
Setting up Antennas
a) Snap AM loop antenna into provided stand, then plug AM antenna cable into AM Loop Antenna socket on back of unit.
a) Snap AM loop antenna into provided stand, then plug AM antenna cable into AM Loop Antenna socket on back of unit.
Move antenna 12” away from unit for best reception.
b) Extend FM Antenna (on back of unit) fully for best reception. Do not strip, alter or attach to other antennas.
c) Locate ZN9 and all antennas away from AC adaptor in wall socket (at least 3 feet) for best radio reception.
Tuning and Playing the Radio
a) Press the
c) Locate ZN9 and all antennas away from AC adaptor in wall socket (at least 3 feet) for best radio reception.
Tuning and Playing the Radio
a) Press the
Radio/Line in Button to select radio play mode. Press as needed to select FM or AM radio band.
b) Turn the Set Wheel to tune radio to a desired station.
c) To program the current station as a preset, press and hold Preset Button 1-2 until P1 flashes on display; press again for P2
c) To program the current station as a preset, press and hold Preset Button 1-2 until P1 flashes on display; press again for P2
and allow to time-out (beep confirmation). Repeat steps a,b,and c for other preset buttons to preset up to 12 stations (6 AM, 6
FM). To listen to a preset station at any time, simply press the desired preset button once or twice.
FM). To listen to a preset station at any time, simply press the desired preset button once or twice.
d) Turn the Volume Wheel to adjust ZN9 volume up or down.
e) Press the EQ Button to select Treble, Bass, 3D sound effect or Balance. Turn the Set Wheel to adjust settings. EQ settings
e) Press the EQ Button to select Treble, Bass, 3D sound effect or Balance. Turn the Set Wheel to adjust settings. EQ settings
for Zune and radio mode are independent.
f) Press the
Button to turn ZN9 off.
Using the Line-in and Line-out Jacks
a) Use an audio patch cord (available at www.ihomeaudio.com) to play nondocking Zune or other audio devices through the ZN9
Line-in Jack (connect one end in the device’s line out or headphones jack, the other in the ZN9 line-in jack). Make sure there is
no Zune docked in the ZN9 when using the line-in jack.
no Zune docked in the ZN9 when using the line-in jack.
b) To listen to your audio device, press the Radio/Line in Button until line-in is displayed, indicating line-in mode. Adjust the output
volume on your line-in device.
c) Use the Line Out Jack to connect the ZN9 to the line-in jack of other audio devices such as a tape recorder or amplifier.
The Volume Wheel of the ZN9 does not control line-out volume (adjust on attached device instead). The Line Out Jack is not
for headphones.
for headphones.
Using Sleep Mode
Sleep mode lets you sleep to your Zune or the radio, gradually lowering the volume until the unit shuts off at the selected time.
a) Press the Sleep Button to select an amount of time before the ZN9 shuts off: 120, 90, 60, 30 or 15 minutes.
b) Turn the Volume Wheel to set the sleep volume (this volume setting is separate from your standard volume setting).
a) Press the Sleep Button to select an amount of time before the ZN9 shuts off: 120, 90, 60, 30 or 15 minutes.
b) Turn the Volume Wheel to set the sleep volume (this volume setting is separate from your standard volume setting).
Using the Dimmer
a) Press the Snooze/Dimmer Button during normal operation to adjust brightness of LCD display. There are 8 levels of brightness
including OFF.