Teknika DAB-109F Manuel D’Utilisation
6
AC MAINS OPERATION
CONNECTING POWER
Check that the mains voltage marked on the rating plate
•
on the back panel is the same as the voltage in your
area.
Plug the AC power cord into the AC inlet
area.
Plug the AC power cord into the AC inlet
•
Plug the mains plug into the wall socket and switch the
•
mains power on.
STANDBY CONTROL
To turn the radio on:
To turn the radio on:
Press the
•
STANDBY/ON button.
The display will light and the radio will tune to the last station
used. If the power has been disconnected, the clock will set.
To turn the power off:
used. If the power has been disconnected, the clock will set.
To turn the power off:
Press the
•
STANDBY/ON button.
The radio and display light will switch off. The clock will
continue to run whilst mains power is connected.
LOW POWER STANDBY
If preferred, you can change the standard Standby mode to
‘Low Power’ standby. In Low Power Standby mode the power
consumption of your radio will be reduced to less than 1W
when set to Standby.
NOTE:- When Low Power Standby mode is set the display will
switch off completely when set to Standby and Alarm and
Sleep functions are disabled.
To change to low-power Standby mode:
continue to run whilst mains power is connected.
LOW POWER STANDBY
If preferred, you can change the standard Standby mode to
‘Low Power’ standby. In Low Power Standby mode the power
consumption of your radio will be reduced to less than 1W
when set to Standby.
NOTE:- When Low Power Standby mode is set the display will
switch off completely when set to Standby and Alarm and
Sleep functions are disabled.
To change to low-power Standby mode:
Press the
•
STANDBY/ON button for at least five
seconds.
To return to normal Standby mode:
Press the
•
STANDBY/ON button for at least five
seconds.
ADJUSTING THE VOLUME
FITTING BATTERIES
Referring to the diagram on the previous page, fit 6 x AA
batteries into the battery compartment. Alkaline batteries
are recommended for best performance.
POWER CONTROL
To turn the radio on:
Referring to the diagram on the previous page, fit 6 x AA
batteries into the battery compartment. Alkaline batteries
are recommended for best performance.
POWER CONTROL
To turn the radio on:
Press the
•
STANDBY/ON button.
The display will light, the radio will tune to the last station
used, and the clock will set.
To turn the power off:
used, and the clock will set.
To turn the power off:
Press the
•
STANDBY/ON button.
The radio and display will switch off.
NOTE:- The STANDBY/ON button functions as a Power On/
Off button during battery operation - the display will switch
off completely when set to Standby and Alarm and Sleep
functions are disabled.
NOTE:- The STANDBY/ON button functions as a Power On/
Off button during battery operation - the display will switch
off completely when set to Standby and Alarm and Sleep
functions are disabled.
BATTERY OPERATION
GETTING STARTED
Dispose of used batteries with regard to the recycling
regulations in your area. Do NOT short circuit batteries or
throw them into water, the general rubbish or in a fire.
Weak batteries can leak and damage the remote control.
Replace them in good time!
regulations in your area. Do NOT short circuit batteries or
throw them into water, the general rubbish or in a fire.
Weak batteries can leak and damage the remote control.
Replace them in good time!
BATTERY DISPOSAL
DAB/FM AERIAL
Before using your radio for DAB or FM reception, always
unclip and fully extend the aerial. The aerial has a rotating
base to enable adjustment for maximum signal strength.
SETTING THE CLOCK
The clock on your radio is automatically set when first used
from the time signal broadcast with DAB radio stations.
The clock is not set by the user.
INITIAL SCAN
When your radio is used for the first time:
The radio scans all usable stations (full scan) and stores them
alphanumerically -1 Radio, 2 Radio, AA Radio, AB Radio...
The initial scan will take a few minutes. After the scan, the
number of stations found will be displayed, the clock will be
set, the radio will display the first station in the sequence and
begin playing at the default system volume of 10.
Note: If no stations are found after the scan, ‘0 Services Found’,
then ‘Service N/A’ will be displayed. If this happens, switch
the radio off and move it to a location with a stronger signal.
When you switch the radio back on it will automatically
repeat the scan process.
Before using your radio for DAB or FM reception, always
unclip and fully extend the aerial. The aerial has a rotating
base to enable adjustment for maximum signal strength.
SETTING THE CLOCK
The clock on your radio is automatically set when first used
from the time signal broadcast with DAB radio stations.
The clock is not set by the user.
INITIAL SCAN
When your radio is used for the first time:
The radio scans all usable stations (full scan) and stores them
alphanumerically -1 Radio, 2 Radio, AA Radio, AB Radio...
The initial scan will take a few minutes. After the scan, the
number of stations found will be displayed, the clock will be
set, the radio will display the first station in the sequence and
begin playing at the default system volume of 10.
Note: If no stations are found after the scan, ‘0 Services Found’,
then ‘Service N/A’ will be displayed. If this happens, switch
the radio off and move it to a location with a stronger signal.
When you switch the radio back on it will automatically
repeat the scan process.
To increase the volume:
Turn the
•
VOLUME/SELECT knob clockwise.
To decrease the volume:
Turn the
•
VOLUME/SELECT knob anti-clockwise.