Lorex Technology LW2002 Series Fascicule

 

Skill Level

Intermediate

easy 

advanced

Time 

under 30 minutes

under 15 minutes

under 60 minutes

Hand Tools

Hardware

Router

Hi Speed

over 60 minutes

Skill Level

Intermediate

easy 

advanced

Time 

under 30 minutes

under 15 minutes

under 60 minutes

Hand Tools

Hardware

Router

Hi Speed

over 60 minutes

Under 15 Min

utes*

Hand Tools

Plug & Play connections, 

On screen set up

* Installation time may vary based on 

application and camera location

The Digital Wireless Surveillance System 

comes with the following components:

1 x Wireless Receiver

1 x Receiver Cradle

1 x Wireless Camera(s)*

1 x Power Adaptor (for receiver)

1 x Power Adaptor (for camera)*

1 x RCA Audio/Video Cable

Instruction Manual

Quick Start Guide
*Number of cameras and power adaptors may vary 

by model. Check your package for specific content 

information.

Wireless cameras require a power source (either an electrical outlet 

or battery power) to operate. 

NOTE: Before you install a camera, carefully plan where and 

how it will be positioned, and where you will route the cable that 

connects the camera to the power adaptor. Before starting permanent 

installation, verify its performance by observing the image on a 

monitor when the camera is positioned where it will be permanently 

installed.

Connect the Power Adaptor to the 9V 

Input on the back of the camera.

When adding cameras that were not included in the original box, 

you will need to pair up the camera with the receiver. Please refer to 

the Camera Pairing Section of the User Manual.

Wall Mounting: Mark the position of 

the screw holes on the wall.

• Drill holes and insert 2 screws.

• Firmly attach the camera to the wall by 

    placing the stand over the installed 

    screws and pushing the base 

    downwards to secure.

Position the Base holes over the

screws. Slide the base downwards.

Camera Positioning: The Camera can be placed on 

a flat surface, or wall mounted. The versatile stand 

allows for several different mounting options.

Desk/Counter Mount

Wall Mount

NOTE: See Page 2 for battery operation instructions.

Night Vision : The camera has built-in IR LEDs, which provides the 

camera with the ability to view images in no/low light conditions. It 

is important to use the provided power adaptor (and not batteries) 

when using the camera for prolonged periods in low light conditions, 

as the built-in IR LEDs will drain the battery more

quickly than during regular daytime use.

Connect one end (black connector 

plug) of the RCA Audio/ Video 

Cable to the Receiver or Receiver 

Cradle. 

Place the Receiver Cradle 

or Receiver in a location 

that offers clear reception 

with your camera(s).

Determine if you will be using the Receiver Cradle, or connecting the cables directly to the receiver before installation.

Plug the AC adaptor power output cable into the 

9V POWER input of the Cradle or directly into the 

Receiver. Plug the power plug into a wall outlet or 

surge protector.

NOTE: Leave the receiver to charge 

for 4 hours prior to first time use so 

the built-in rechargeable receiver 

battery is fully charged. DO NOT 

remove the power cable from the 

receiver / from the cradle during 

initial charging process. After initial 

charge, charge as required. 

Once the Receiver is fully charged the 

LED light above the DC 9V input on the 

receiver will turn from RED to GREEN.

Connect the other ends (Audio 

- white plug, Video - Yellow plug) 

of the RCA cable to your Monitor 

or TV.

Turn on Monitor or TV, and switch to 

the video channel that the receiver has

been connected to.

NOTE: The purpose of the AV output is for convenience only. When using with large 

screen TV/Monitor, the picture might be grainy as the camera limits video resolution to 

VGA (640x480 pixels). This is not a product defect. For best performance use with 

TV/Monitor PIP (Picture in Picture) function. Check your TV/Monitor product manual to 

see if this feature is available on your TV/Monitor. This allows you to view TV or other 

video source and see video from the camera in a small window on the same screen.

View your Receiver images on any Monitor or TV 

with RCA inputs (note that this requires the receiver 

to be connected to AC power, not battery power).

 If your TV has a PIP feature, you 

can have the camera images displayed in 

the PIP window. Check your TV manual 

for info on PIP feature (if available).

NOTE: AVOID INSTALLING IN 

A LOCATION WHICH REQUIRES 

THE WIRELESS SIGNAL TO PASS 

THROUGH CEMENT, CONCRETE 

AND METAL STRUCTURES. THIS 

WILL REDUCE THE 

TRANSMISSION RANGE.

NOTE: The receiver monitor turns off 

when it is connected to a Monitor or TV.

Set the alarm sensitivity on the camera. 

Turn the wheel on the side of the camera 

all the way down to decrease sound 

sensitivity. This means that the alarm is 

only triggered by loud noises. Turning 

the wheel the other way will result in 

the opposite. See the User’s Manual for 

complete details on the alarm function.

 Connect to RCA input on a VCR, 

DVD recorder or Surveillance DVR to 

record video from the LW2002 system.