JVC GYHM150U Manuel D’Utilisation
46
4
Resume recording. (Recording 2)
● Press the [REC] button again to resume recording. The
display changes from
● The card slot status indicator continues to blink in green.
5
Pause recording.
● Press the [REC] button again to pause recording. The
display changes from
● The card slot status indicator continues to blink in green.
6
Resume recording. (Recording 3)
● Press the [REC] button again to resume recording. The
display changes from
● The card slot status indicator continues to blink in green.
7
Press and hold the [REC] button or press the user
button that is assigned with
recording. (
● Recording stops and the display changes from
ARECCBBASTBYCB. A AclipB is generated.
● The card slot status indicator lights up in green.
8
Press the [REC] button again.
● The status display changes from ASTBYCBBARECCB and
the card slot status indicator blinks in green.
● A new AclipB is generated from here.
Memo :
● The following operations cannot be performed while
recording is paused (STBYC, yellow text).
• Clip Review operation (A Page 28)
• Switching SDHC/SDXC card slots
• Switching operation mode (A Page 13)
• Clip Review operation (A Page 28)
• Switching SDHC/SDXC card slots
• Switching operation mode (A Page 13)
Note :
● Do not remove the SDHC/SDXC card during recording
(RECC, red text) or recording pause (STBYC, yellow text).
● To remove the SDHC/SDXC card in AClip ContinuousB
mode, press the user button assigned with
press and hold the [REC] button, check that
(white text) is displayed and the card slot status indicator is
lighted in green before you remove the card.
lighted in green before you remove the card.
● When the SDHC/SDXC card becomes full during recording,
recording stops and
ASTOPB is displayed.
● When the power is turned off during recording or recording
pause, recording stops and power is cut off after a clip is
generated.
generated.
● If the power is cut off due to low battery power, a proper clip
may not be generated.
Frame Rec
In normal recording, when the recording stops, the image and
accompanying data from the start till the end of the recording
are recorded as one
accompanying data from the start till the end of the recording
are recorded as one
AclipB on the SDHC/SDXC card.
In this mode, recording starts with every press of [REC], and
only the specfied number of frames is recorded. The
recording can be written to the media as a single clip until it
is stopped.
only the specfied number of frames is recorded. The
recording can be written to the media as a single clip until it
is stopped.
Memo :
● Audio cannot be recorded.
● Until a specified amount of recordings is accumulated, the
file will not be written to the media.
● If the specified amount is not reached when recording is
stopped, normal recording is performed and frames are
added to the ending of the clip until the amount is
reached. (Padding)
added to the ending of the clip until the amount is
reached. (Padding)
● After the specified number of frames is recorded and written
to the media, recording will be performed until the same
number is accumulated again.
1
● The status display changes from ASTBYBBASTBYFB.
2
Set the number of frames to record in [Rec Frames].
Set using [Main Menu]
3
Start recording.
● Press the [REC] button to record only the number of frames
specified in [Rec Frames] and pause.
● The status display changes from
ASTBYFBBARECFBBASTBYFB (yellow text).
● The card slot status indicator blinks in green.
Actual clip recorded to media
Press [REC]
(Frame Rec starts)
(Frame Rec starts)
Press and hold [REC]
(Frame Rec stops)
Specified amount of data
Pause
Recording resumes
Pause
Pause
Normal recording
(Padding data)
Recording of specified number of frames in [Rec Frames]
Press [REC]
Recording resumes
GY-HM150U.book Page 46 Monday, September 5, 2011 1:48 AM