Sony DVW-970P Manuel D’Utilisation
118
Audio Input System
Chap
te
r
7
Set
ting Up th
e Camc
orde
r
For the operation of the WRR-855A/855B, refer to the
manual supplied with the WRR-855A/855B.
manual supplied with the WRR-855A/855B.
• When the XLR connection automatic detection function
is on, even if the AUDIO IN CH-1 or CH-2 switch is set
to WIRELESS, the signal input to the AUDIO IN CH1
or CH2 connector is automatically selected when an
audio cable is connected to the AUDIO IN CH1 or CH2
connector. In such a case, set REAR XLR AUTO to OFF
on the AUDIO-1 page of the MAINTENANCE menu.
to WIRELESS, the signal input to the AUDIO IN CH1
or CH2 connector is automatically selected when an
audio cable is connected to the AUDIO IN CH1 or CH2
connector. In such a case, set REAR XLR AUTO to OFF
on the AUDIO-1 page of the MAINTENANCE menu.
• The audio signals to be recorded on audio channels 3 and
4 depend on the settings of the AUDIO IN CH-3/CH-4
switches without being affected by the XLR connection
automatic detection function.
switches without being affected by the XLR connection
automatic detection function.
Fitting the WRR-862 (with a battery pack)
1
(1) Attach the WRR tuner fitting (not supplied, service
part number: A-8278-057-A) to the back of the
camcorder.
camcorder.
1
Use a Phillips-type screwdriver to tighten the
four screws placed in the tuner fitting. For three
of these screws, insert the screwdriver through
the corresponding hole and tighten the screw.
four screws placed in the tuner fitting. For three
of these screws, insert the screwdriver through
the corresponding hole and tighten the screw.
2
Loosen the adjustment screws.
3
Adjust the tuner fitting position for a battery
pack to be attached, and tighten the adjustment
screws to fix its position.
pack to be attached, and tighten the adjustment
screws to fix its position.
4
Attach the mount plate supplied with the WRR-
862.
862.
(2) Attach the battery pack.
For details about attaching the battery pack, see “7-1-
1 Using a Battery Pack” on page 110.
1 Using a Battery Pack” on page 110.
2
Mount the tuner on the WRR tuner fitting.
3
Connect the tuner power cord to the DC OUT
connector of the camcorder, and the audio output cable
to the AUDIO IN CH1 or CH2 connector.
connector of the camcorder, and the audio output cable
to the AUDIO IN CH1 or CH2 connector.
Notes
WRR-855A/855B
Set the AUDIO IN switch to WIRELESS.
Back of camcorder
Battery Pack
Adjustment screws
Mount plate (supplied
with WRR-862)
with WRR-862)
Screwdriver
WRR-862
LINE/MIC/+48 V ON
switch:
Set the LINE/MIC/
+48 V ON switch for
the channel to which
the audio out cable is
attached to MIC.
switch:
Set the LINE/MIC/
+48 V ON switch for
the channel to which
the audio out cable is
attached to MIC.
AUDIO IN CH-1/CH-2 switches:
When the XLR connection
automatic detection function is
set to OFF on the AUDIO-1 page
of the MAINTENANCE menu,
set the AUDIO IN CH-1 or CH-2
switch for the channel to which
the audio output cable is
connected to REAR.
When the XLR connection
automatic detection function is
set to OFF on the AUDIO-1 page
of the MAINTENANCE menu,
set the AUDIO IN CH-1 or CH-2
switch for the channel to which
the audio output cable is
connected to REAR.
to AUDIO IN CH1 or
CH2 connector
CH2 connector
to DC OUT connector