Sony Ericsson PDW-530P Manuel D’Utilisation
Chap
te
r
7
v
in
g
and Lo
adin
g
Us
e
r S
e
ttin
g Dat
a
107
7-2 Saving and Loading Scene Files
5
Turn the MENU knob to move the
b mark to the
desired file number to be loaded, and press the MENU
knob.
knob.
The message “LOAD OK? YES
b NO” appears and
the access indicator lights.
6
To carry out the load, move the
b mark to “YES” and
press the MENU knob.
To cancel, press the MENU knob leaving the
To cancel, press the MENU knob leaving the
b mark
pointing to “NO”.
When the load is completed, the message
“COMPLETE” appears and the access indicator goes
off.
The USER FILE page appears again.
“COMPLETE” appears and the access indicator goes
off.
The USER FILE page appears again.
7
To end the menu operation, set the MENU ON/OFF
switch to OFF or close the cover of the menu operating
section.
switch to OFF or close the cover of the menu operating
section.
If data cannot be loaded
If one of the following error messages appears during or
after the load operation, then the data was not loaded.
If one of the following error messages appears during or
after the load operation, then the data was not loaded.
Data load error messages
7-2 Saving and Loading
Scene Files
You can save various settings for shooting a particular
scene as a scene file. Loading the scene file, you can
quickly recreate setup conditions suitable for the scene.
You can save up to five scene files in the camcorder
memory and up to 100 scene files in a “Memory Stick”.
You can also load data from the “Memory Stick” into the
camcorder memory.
scene as a scene file. Loading the scene file, you can
quickly recreate setup conditions suitable for the scene.
You can save up to five scene files in the camcorder
memory and up to 100 scene files in a “Memory Stick”.
You can also load data from the “Memory Stick” into the
camcorder memory.
Data that can be saved in a scene file
You can save the following data in a scene file:
• Values adjusted using the PAINT menu
• Values adjusted using the PAINT menu
For details of the PAINT menu, refer to the Maintenance
Manual.
Manual.
• Shutter speed settings made in the standard mode and
ECS mode
• The white balance data included in a scene file depends
on the SCENE WHITE DATA setting on the
REFERENCE page of the FILE menu.
REFERENCE page of the FILE menu.
7-2-1 Saving a Scene File
Proceed as follows to save a scene file in the camcorder
memory or the “Memory Stick”.
memory or the “Memory Stick”.
Note
To save a scene file in the “Memory Stick”, insert the
“Memory Stick” before starting the operation.
“Memory Stick” before starting the operation.
1
In the TOP menu, select the FILE menu.
2
Turn the MENU knob until the SCENE FILE page
appears, then press the MENU knob to select the page.
Alternatively, select “SCENE FILE” on the
CONTENTS page to display the SCENE FILE page.
appears, then press the MENU knob to select the page.
Alternatively, select “SCENE FILE” on the
CONTENTS page to display the SCENE FILE page.
Error message
Cause
Action
NO MEMORY
STICK (flashing)
STICK (flashing)
No “Memory
Stick” is inserted.
Stick” is inserted.
Insert or reinsert the
“Memory Stick”.
“Memory Stick”.
MEMORY STICK
ERROR
(flashing)
ERROR
(flashing)
Circuit or
“Memory Stick”
fault.
“Memory Stick”
fault.
Recheck, and
consult your Sony
representative.
consult your Sony
representative.
FILE ERROR
(flashing)
(flashing)
The “Memory
Stick” contains
data that cannot
be loaded into this
camcorder.
Stick” contains
data that cannot
be loaded into this
camcorder.
Do not try to load
data saved from
another camcorder.
data saved from
another camcorder.
P00 USER LOAD
DISPLAY MODE : ALL
001.USER1 JAN/01/04
002.USER2 JAN/15/04
003.NO FILE
004.USER4 FEB/05/04
005.USER5 FEB/20/04
ESC
P00 USER LOAD
LOAD OK? YES NO
DISPLAY MODE : ALL
001.USER1 JAN/01/04
002.USER2 JAN/15/04
003.NO FILE
004.USER4 FEB/05/04
005.USER5 FEB/20/04
ESC
04 SCENE FILE
s1 :STANDARD
s2 :STANDARD
s3 :STANDARD
s4 :STANDARD
s5 :STANDARD
sSTANDARD
SCENE RECALL : EXEC
SCENE STORE : EXEC
F.ID:
TOP