Crimestopper Security Products CS-2002DPII Manuel D’Utilisation
4
WIRING
BLACK WIRE: SYSTEM CHASSIS GROUND
The Black wire MUST be connected the CHASSIS METAL of the vehicle. Scrape away any paint or debris
from the connection point and use a star washer to ensure a good connection. Keep the ground wire short.
The Black wire MUST be connected the CHASSIS METAL of the vehicle. Scrape away any paint or debris
from the connection point and use a star washer to ensure a good connection. Keep the ground wire short.
YELLOW WIRE: IGNITION SWITCHED “ON” AND “START” +12 VOLTS
Connect to an IGNITION wire (or fuse in the fuse box) that shows +12 Volts when the key in both “On” and
“Start” (WHEN CRANKING) positions.
Connect to an IGNITION wire (or fuse in the fuse box) that shows +12 Volts when the key in both “On” and
“Start” (WHEN CRANKING) positions.
GRAY WIRE: (-) NEGATIVE AUX REMOTE OUTPUT 1 (Optional, may require a relay)
Connect to the Negative trunk release circuit or to the activation circuit of an auxiliary module or device. If the
circuit requires +12V, then a relay is required. RELAY WIRING: Connect the Gray wire to terminal 85, connect
relay terminals 86 and 87 to +12V constant power. Connect terminal 30 of the relay to the +12V positive
device/circuit to be activated.
Connect to the Negative trunk release circuit or to the activation circuit of an auxiliary module or device. If the
circuit requires +12V, then a relay is required. RELAY WIRING: Connect the Gray wire to terminal 85, connect
relay terminals 86 and 87 to +12V constant power. Connect terminal 30 of the relay to the +12V positive
device/circuit to be activated.
BLUE WIRE: (-) NEGATIVE HOOD/TRUNK TRIGGER (Optional)
Input trigger for a grounding hood or trunk pin switch. Connect to existing hood and trunk pin switches that
read ground when open. If no existing switches are available, install new pin switches if desired. Note: DO
NOT mount new pin switches in water pathways.
Input trigger for a grounding hood or trunk pin switch. Connect to existing hood and trunk pin switches that
read ground when open. If no existing switches are available, install new pin switches if desired. Note: DO
NOT mount new pin switches in water pathways.
BLACK/WHITE WIRE: (-) NEGATIVE DOME LIGHT ILLUMINATION OUTPUT (Optional, requires a relay)
This wire provides a (-) negative ground when the system is disarmed to activate a vehicles dome light circuit.
We recommend the use of a relay for this connection. Connect Black/White to terminal #85 of relay. Connect
terminal #86 to fused constant +12V. Connect terminal #87 to a +12V constant or ground source depending
on the type of dome light circuit in the vehicle. Connect Terminal #30 to the dome light circuit in the vehicle.
This wire provides a (-) negative ground when the system is disarmed to activate a vehicles dome light circuit.
We recommend the use of a relay for this connection. Connect Black/White to terminal #85 of relay. Connect
terminal #86 to fused constant +12V. Connect terminal #87 to a +12V constant or ground source depending
on the type of dome light circuit in the vehicle. Connect Terminal #30 to the dome light circuit in the vehicle.
BROWN/WHITE WIRE: (-) NEGATIVE HORN PULSE / CHIRP OUTPUT (Optional, may require a relay)
Connect to the Negative Horn Trigger wire usually located near the steering column. If the vehicle horn circuit
requires +12V, then a relay is required.
Connect to the Negative Horn Trigger wire usually located near the steering column. If the vehicle horn circuit
requires +12V, then a relay is required.
ORANGE WIRE: (-) NEGATIVE ARMED OUTPUT (500mA Ground, Optional)
This wire becomes a constant Ground output when system is armed. This output can be used to activate
optional devices such as extra sensors, LED’s, window roll-up modules, voice modules etc.
This wire becomes a constant Ground output when system is armed. This output can be used to activate
optional devices such as extra sensors, LED’s, window roll-up modules, voice modules etc.
WHITE/RED WIRE: (-) NEGATIVE AUX REMOTE OUTPUT 2 (Optional, may require a relay)
This wire connects the same way as Remote Output 1 see GRAY WIRE description above.
This wire connects the same way as Remote Output 1 see GRAY WIRE description above.