Skylink PS-103 Fascicule

The Motion Sensor is designed to monitor movement around / within 
your house.  Once motion is detected, the control panel will either alert 
you or alarm will be triggered.  

In this package, you should find a motion sensor, ball-head joint, and 
screws.

Please follow the instructions below to set up the motion sensor.

Insert a 9V alkaline battery 
(Not included) to the motion 
sensor and its LED will be 
on for 2 seconds. 

Control Panel will not respond to Motion Sensor unless: 
1) The Control Panel is armed in Away Mode, it will respond to Motion 
    Sensors in Zones 1, 2 and 3; 
2) Motion Sensor is programmed into Zone 4, which is a dedicated Alert 
    Zone. 

It is important to select which zone you program the motion sensor to. 

- If you setup the motion sensor for security purpose where it will cause 
  an alarm when an intruder break-in, you should program the Motion 
  Sensor to either Zone 1, 2 or 3. DO NOT program to Zone 4 as it is a 
  dedicated Alert Zone, sensors in this zone will not cause an alarm.
 
- If you setup the motion sensor for alert purpose where it does not need 
  to cause an alarm when motion is detected, you should program the 
  Motion Sensor to Zone 4. DO NOT program to Zone 1, 2, or 3 as Motion 
  Sensor in these zones will not provide any alert beeping indication. 

Therefore, please select which zone you need to program the Motion 
Sensor before proceeding further. 

Step 1: 
Press and hold the Learn Button on the Control Panel for 3 seconds. 
Control Panel beeps once and you may release the Learn Button. 

Step 2: 
Press the zone button (1, 2, 3, or 4) once, for which you want to program 
the sensor to. The selected Zone LED will flash. 

MU

TE
MU

TE

IN

PU

T 

  D

C 

 12

V

IN

PU

T 

  D

C 

 12

V

LE

AR

N

LE

AR

N

AL

ER

T

AL

ER

T

CH

IM

E

CH

IM

E

OF

F
OF

F

Step 3: 
Activate the Motion Sensor by pressing the test button on the back of the 
Motion Sensor. 

Step 4: 
You will hear a long beep and the zone LED stops flashing. The sensor 
is now programmed to the Control Panel. 

After programming the motion sensor to the Control Panel, you may 
place the Control Panel in Test Mode to verify the communication 
between the Motion Sensor and the Control Panel. 

Step 1: 
Remove the adapter and all batteries from the Control Panel. 

Step 2: 
Press and hold the "Mute" button and plug the AC adapter back into the 
Control Panel. All LED indicators will be ON, you may release the "Mute" 
button. Control Panel is now in Test Mode, and it will respond to all 
Motion Sensors and other sensors. 

Step 3: 
Place the Alert Notification Switch to "Alert" and you may now activate 
the Motion Sensor by pressing the test button on the back of the Motion 
Sensor. You may also move in front of the Motion Sensor. Please refer 
to "Walk Testing" for detail information on how to walk test the Motion 
Sensor. 

Step 4: 
Control Panel will respond by flashing the zone LED and alert beeping, 
according to the zone number. 1 beep for zone 1, 2 beeps for zone 2 etc. 
The beeping will last around 15 seconds for each activation. 

After testing, unplug the AC adapter and plugs it back into the Control 
Panel, it will back to Normal Operating Mode. 

You may now close the battery 
cover and re-insert the screw. 
Mount the ball-head joint on 
the wall with screws provided.  
Slide the back of the sensor into 
the ball-head joint. The mounting 
angle can be adjusted.

 

Walk test should be performed after the motion sensor 
is mounted.  Walk in the detected area, if motion is 
detected, a red light inside the sensor will glow.  If the 
red light does not glow, motion has not been detected 
and you may need to re-position the sensor.  Ensure 
you walk test all the locations that you would like the 
motion sensor to cover.