Bosch D625 Manuel D’Utilisation
D623 Series/D625 Series | User's Guide | Control Panel Event Descriptions
.
Bosch Security Systems | 9/04 | 46841E
35
Table 8: Control Panel Event Descriptions (continued)
Event #
Event
Description
Event #
Event
Description
86
AllCom Low
Signl
Signl
Low signal strength detected on
alternate communication device.
alternate communication device.
110
Output Set,
Skd
Skd
Relay set by sked.
87 Missing,
Alarm
Point assigned to point expander
(wired or RF) not responding to
control panel status poll while
system is armed.
(wired or RF) not responding to
control panel status poll while
system is armed.
111 Output
Set,
RAM IV
Relay set by RAM IV.
88
Missing,
Trouble
Trouble
Point assigned to point expander
(wired or RF) not responding to
control panel status poll while
system is armed.
(wired or RF) not responding to
control panel status poll while
system is armed.
112
Rstrl, Tamper
Restoral from alarm, Tamper point
type.
type.
89
Open, Skd
Opening by sked.
113
Rstrl,
Emergency
Emergency
Restoral from alarm, Emergency
point type.
point type.
90
Open, RAM
IV
IV
Opening by RAM IV.
114
Rstrl, Panic
Restoral from alarm, Panic point
type.
type.
91
Open, Usr
Opening by user, by ID reported.
115
Rstrl, Invisible
Restoral from alarm, Invisible point
type.
type.
92
Open, KS
Opening by keyswitch.
116
Rstrl,
24-hr Burg
24-hr Burg
Restoral from alarm, 24-hour burglary
point types.
point types.
93 Open,
Skd,
Alarm
Opening after alarm event by sked.
117
Rstrl, Cntrl, Dly
Restoral from alarm, controlled point
types.
types.
94
Open, RAM
IV, Alarm
IV, Alarm
Opening after alarm event by
RAM IV.
RAM IV.
118
Rstrl, Cntrl
Restoral from alarm, controlled point
types.
types.
95 Open,
Usr,
Alarm
Opening after alarm event, ID
reported.
reported.
119
Rcvr Jam
Jammed condition detected on
premises RF receiver.
premises RF receiver.
96
Open, KS,
Alarm
Alarm
Opening after alarm event by
keyswitch.
keyswitch.
120
Rcvr Jam Rstl
Jammed condition detected on
premises RF received cleared.
premises RF received cleared.
97 Point
Opening
Point opened by Independent
Point Control device.
Point Control device.
121 RF
Battery
Low
Low battery detected on premises
RF transmitter.
RF transmitter.
98
Params
Changed
Changed
Panel parameters changed.
122
RF Battery
Rstl
Rstl
Low battery condition detected on
premises RF transmitter cleared.
premises RF transmitter cleared.
99 Phone
Line
Fail
Phone the voltage less than 3 V for
40 sec.
40 sec.
123
RF Tamper
Trbl
Trbl
Premises RF Transmitter Tamper
Trouble.
Trouble.
100
Phone Line
Rstl
Rstl
After Phone Line Fail event, phone
line voltage detected at greater
than
3 V for 40 sec.
line voltage detected at greater
than
3 V for 40 sec.
124
RF Tamper
Rstl
Rstl
Premises RF Transmitter Tamper
Restoral.
Restoral.
101
Bad Call to
RAM IV
RAM IV
Panel attempted to call RAM IV but
was unsuccessful.
was unsuccessful.
125
SDI Missing
SDI device not responding to
polling.
polling.
102
RAM IV
Access Fail
Access Fail
RAM IV attempted to connect to
control panel but was
unsuccessful.
control panel but was
unsuccessful.
126
SDI Missing,
Rstl
Rstl
SDI device declared as missing
now responding to polling.
now responding to polling.
103 RAM
IV
Access OK
RAM IV successfully connected
and disconnected from control
panel.
and disconnected from control
panel.
127
SDI Tamper
Tamper open on SDI Device
Tamper.
Tamper.
104
Re-Boot,
Panel
Panel
Normal start-up or reset with
installer switch.
installer switch.
128
SDI Tamper,
Rstl
Rstl
SDI Device Tamper restored.
105
Re-Boot SDI
Unexpected reset (reboot) from
SDI device.
SDI device.
129
SDI Trouble
Trouble detected on SDI device.
106
Output Reset,
Usr
Usr
Relay reset by user.
130
SDI Trouble,
Rstl
Rstl
SDI (option bus) device trouble
condition cleared.
condition cleared.
107 Output
Reset,
Skd
Relay reset by sked.
131
SDI Over
Current
Current
Over current condition detected on
SDI device.
SDI device.