Procom ML300HGA Manuel D’Utilisation

 WARNING:  If  you  do  not

follow  these instructions exactly,
a fire or   explosion  may  result
causing    property     damage,
personal  injury  or  loss  of  life.

A.     This   appliance   has  a  pilot
which  must  be  lighted  by  hand.
When  lighting  the  pilot,  follow  these
instructions  exactly.
B.     BEFORE  LIGHTING  smell  all
around  the  appliance  area  for  gas.
Be  sure  to  smell  next  to  the  floor
because  some  gas  is  heavier  than
air  and  will settle on  the  floor.

 

  Do not  try  to light any appliance.

 

  Do    not    touch    any    electric

switch,  do  not  use any   phone

         in your building.

 

 Immediately   call    your   gas

supplier   from  a   neighbor’s
p h o n e .     F o l l o w     t h e     g a s

        supplier’s  instructions.

 

 if  you  cannot  reach  your gas

supplier,         call        the         fire

         department.

C.      Use  only   your  hand  to  push in
or  turn  the  gas  control  knob.
Never  use  tools.  If  the  knob  will
not  push  in  or  turn  by  hand,  don’t
try  to  repair  it , call  a  qualified
service  technician  or  gas  supplier.
Force  or  attempted  repair  may
result  in  a  fire  or  explosion.
D.     Do  not  use  this  appliance  if any
part  has  been  under  water.
Immediately  call  a  qualified  service
t e c h n i c i a n     t o     i n s p e c t     t h e
appliance  and  to  replace  any  part of
the  control  system  and  any gas
control  which  has  been   under   water.

1.     STOP!      Read        the      safety

information on the side of  heater.

2.      Check      that     gas     supply    to
         heater  is  on.
3.       Push   in   control     knob   slightly

and  turn   clockwise 

  to  the

        OFF position.(see  Figure  19)
         NOTE:  Knob  cannot  be  turned

from 

"

PILOT 

"

 to 

"

OFF

"

  unless

knob is  pushed  in  slightly.  Do

        not  force.
4.      Wait   five  minutes   to   clear    out

any gas. Then smell for gas, in-
cluding  near  the floor. If you smell
gas.STOP! Follow 

"

B

"

 in the

safety information on the side of
heater. If you don’t smell gas. go

        to  the  next  step.
5.      Push  in  and   turn  control  knob

counterclockwise  

   to  PILOT

position.  Press  in  control knob

        for  five(5)  seconds.
         Note:  You   may   be    running

this  heater  for  the  first time
after  hooking  up  to  gas  supply.
If  so,  you  may   need  to  press in
control  knob  for  30  seconds. This
will  allow  air  to  bleed  from

        the  gas  system.

6.      With    control    knob  pressed   in,

push  down  and  release  the
ignitor  button. This  will  light
pilot.  If  needed,  keep  pressing

         ignitor  button  until  pilot  lights.
7.       Keep   control    knob   depressed

for ten (10) seconds after lighting
pilot.  If  pilot  goes out, repeat

         steps  5,6 and 7.
8.      To  select   the   desired   heating

level, partially press down the
control  knob slightly  and  rotate

counterclockwise 

 .  Release

the downward  pressure  on  the
knob  while  continuing  to  turn
until the  knob  locks  at  the
desired setting  position.  Do  not

     operate   between  locked
         positions.

1.      Turn   control   knob  clockwise 
        to  the  OFF  position.
2.     Turn  off  all  electric  power  to  the

appliance  if  service  is  to

        be  performed.
Shutting  Off  Burner  Only  (pilot
stays  lit )
Slightly   press   in   control   turn
control   knob clockwise  

  to the

PILOT   position.

1.     Remove  lower  front  panel (see
        Figure 7 page 7).
2.   Follow   steps   1   through  5
        under Lighting Instructions.
3.     With   control   knob   pressed  in,
        strike    match.    Hold   match    to
         pilot until pilot lights.
4.     Keep  control  knob  pressed  in
      for 30  seconds  after lighting
        pilot.  After  30  seconds, release
      control   knob.  Follow   step  8
        under  Lighting  Instructions.
5.     Replace   lower  front   panel.