AdobeAir MS524 Manuel D’Utilisation
Project Submittal Sheet
Models MD/MS 524, MD/MS/MU 628 — U.L. Classifi ed or UD/US 960, UD/US 980 — U.L. Listed
Project
SHL*
Location
Architect
Engineer
Contractor
Submitted
By
Date
*Total design sensible heat load of project.
Blower Section – Motor – Motor Sheave – Pulley and Belt Kit
Blower Section
Motor Specifi cations
Kits
Ref. No.
Qty.
Model No.
Motor HP
Volts
Phase
Amps
Motor Sheave
Belt
1
2
3
4
*NOTE: Each unit (ready to operate) consists of one blower section, one blower motor, one pulley-belt kit, one motor sheave.
Wet Section – Pump
Wet
Section
Pump
Ref. No.
Qty.
Model No.
Quantity Volts
Amps
GPM
1
2
3
4
*NOTE: Each wet section (ready to operate) consists of one wet module and one pump.
Your local MasterCool Representative of AdobeAir, Inc., is ready to
assist you in unit selection and application.
assist you in unit selection and application.
The world leader in evaporative cooling technology, AdobeAir, Inc. is continually involved in
the process of product improvement. AdobeAir, Inc. therefore reserves the right to change
specifi cations and/or design without prior notice. To obtain the most current product information
and/or specifi cations, visit the AdobeAir, Inc. web site at www.AdobeAir.com.
the process of product improvement. AdobeAir, Inc. therefore reserves the right to change
specifi cations and/or design without prior notice. To obtain the most current product information
and/or specifi cations, visit the AdobeAir, Inc. web site at www.AdobeAir.com.
MasterCool evaporative coolers and components are designed and tested in accordance with
one or more of the following standards or agencies:
Air Delivery: Data published derived from tests conducted in accordance with A.M.C.A. (Air Move-
ment and Control Assoc.) Standard 210.
Sealant: Water Immersion: per ASTM D870. Flexibility: per ASTM D756. Corrosion Resistance: per
ASTM B117. Cycle Freeze/Thaw: per ASTM C117.
POLYBOND®: Corrosion Resistance: per ASTM B117. Pencil Hardness: per ASTM D3363. Adhesion:
per ASTM D3359. Impact Resistance: per ASTM D2794. Flexibility: per ASTM D522. Specular Gloss:
per ASTM D523. Surface Burning Characteristics of Building Materials (best rating) per U.L. 723
and ASTM E-84.
Pumps: Recognized under the U.L. component recognition program for the application – construc-
tion, thermal overload, running overload, and locked rotor protection.
Blower Motors: U.L. Recognized general purpose drip-proof.
Polymeric Materials: Tested in accordance with U.L. 94 and 746C. Covered by City of Los Angeles
Research Reports (C.O.L.A.) RR930224 (for all single phase applications), or RR930190 (for 3
phase applications) Electrical, and RR8141 Mechanical.
one or more of the following standards or agencies:
Air Delivery: Data published derived from tests conducted in accordance with A.M.C.A. (Air Move-
ment and Control Assoc.) Standard 210.
Sealant: Water Immersion: per ASTM D870. Flexibility: per ASTM D756. Corrosion Resistance: per
ASTM B117. Cycle Freeze/Thaw: per ASTM C117.
POLYBOND®: Corrosion Resistance: per ASTM B117. Pencil Hardness: per ASTM D3363. Adhesion:
per ASTM D3359. Impact Resistance: per ASTM D2794. Flexibility: per ASTM D522. Specular Gloss:
per ASTM D523. Surface Burning Characteristics of Building Materials (best rating) per U.L. 723
and ASTM E-84.
Pumps: Recognized under the U.L. component recognition program for the application – construc-
tion, thermal overload, running overload, and locked rotor protection.
Blower Motors: U.L. Recognized general purpose drip-proof.
Polymeric Materials: Tested in accordance with U.L. 94 and 746C. Covered by City of Los Angeles
Research Reports (C.O.L.A.) RR930224 (for all single phase applications), or RR930190 (for 3
phase applications) Electrical, and RR8141 Mechanical.
Manufactured in Mexico by:
AdobeAir, Inc.
1450 East Grant St.
Phoenix, AZ 85034
www.AdobeAir.com
AdobeAir, Inc.
1450 East Grant St.
Phoenix, AZ 85034
www.AdobeAir.com
L900799A March 2007