Regency P33-NG4 Manuel D’Utilisation
Regency
®
P33-4 Zero Clearance Direct Vent Gas Fireplace
39
INSTALLING THE OPTIONAL FAN
120 Volt AC power is needed for the fan switch
and blower. The fan can be hard wired if desired.
The receptacle box should be installed on the
left hand side of the unit by a qualifi ed electrician.
The neutral (wider) slot of the polarized
receptacle should be at the top.
and blower. The fan can be hard wired if desired.
The receptacle box should be installed on the
left hand side of the unit by a qualifi ed electrician.
The neutral (wider) slot of the polarized
receptacle should be at the top.
Unit must be grounded at all times. Do
not cut the ground terminal off under any
circumstances.
not cut the ground terminal off under any
circumstances.
1) Shut the power off.
2) Remove the standard fl ush door and the
optional bay door, if installed. Open the
bottom louver door.
bottom louver door.
3) Loosen the 2 screws holding the Burner
ON/OFF switch and bracket to the bottom
louver and lift the assembly out.
louver and lift the assembly out.
4) Turn the fan base on its side (with the base
facing towards you) and then slide the fan
in towards the rear of the unit. Turn the fan
upright and slip it over the two mounting
studs. Take care not to damage the insulation
on the fan base. Ensure that the fan blades
do not rub against the valve tubing.
Diagram 1.
in towards the rear of the unit. Turn the fan
upright and slip it over the two mounting
studs. Take care not to damage the insulation
on the fan base. Ensure that the fan blades
do not rub against the valve tubing.
Diagram 1.
5) Connect fan ground cable to ground lug.
Refer to wiring diagram.
6) Slide the thermodisc/cover assembly into
the bracket clip on the underside of the
fi rebox. Check that no wire will touch the
hot surfaces. Diagram 2.
fi rebox. Check that no wire will touch the
hot surfaces. Diagram 2.
7) Attach the Fan control box to the Burner
ON/OFF control box. Diagram 3.
11) Attach the two control boxes to the bottom
louver and tighten the 2 screws on the left
side and 1 screw on the right side.
side and 1 screw on the right side.
Secure left side with 2 screws.
Secure right side with one screw.
Secure the 2 boxes together
with one screw.
Hold control box assembly in place and
mark the position of the right side slot
Diagram 1
Diagram 2
Diagram 3: Use the clip & hook on the side of
the control boxes to join them together.
8) Secure the two boxes together with one
screw.
9) Position the control box assembly on the
bottom louver and mark the position of the
slot on the right side bracket.
slot on the right side bracket.
Push hold-down clip onto inside louver
and press tab until it is at 90
and press tab until it is at 90
o
to louver.
10) Remove the control box assembly and push
the hold-down clip onto the louver. Bend the
tab until it is at 90
tab until it is at 90
o
to the louver.
12) Secure the fan wires and power cord by
attaching one of the adhesive backed
wire holder clips (Part #910-199) onto
the Fireplace base. Use the second clip
to bundle up the wires approximately 4"
from the control box. Ensure that there is
no interference with the wires when the
louver is closed and that no wire will touch
the hot metal surfaces or sharp edges.
wire holder clips (Part #910-199) onto
the Fireplace base. Use the second clip
to bundle up the wires approximately 4"
from the control box. Ensure that there is
no interference with the wires when the
louver is closed and that no wire will touch
the hot metal surfaces or sharp edges.
13) Plug the fan power cord into the rear end of
the receptacle box to provide the maximum
clearance from the louvers.
clearance from the louvers.
TO REMOVE THE FAN
1) Shut the power off.
2) Reverse the above instructions.
Note: The bearings are lubricated for life.
Do not lubricate them. Make sure
you vacuum the fan area on a regular
basis.
you vacuum the fan area on a regular
basis.
IMPORTANT:
These fans collect a lot of dust from within
your home. Ensure you maintain these fan
motors on a regular basis by vacuuming
out the fan blades and housing using a
soft brush nozzle.
your home. Ensure you maintain these fan
motors on a regular basis by vacuuming
out the fan blades and housing using a
soft brush nozzle.
INSTALLATION