Johnson Controls ACPU024 THRU 060 Manuel D’Utilisation
279815-PTG-D-0408
Johnson Controls Unitary Products
29
MECHANICAL SPECIFICATIONS
GENERAL DESCRIPTION
Units shall be factory-assembled, single packaged, Electric
Cooling units, designed for outdoor mounted installation. ACP
units shall have minimum SEER ratings of 13. They shall have
built in, equal size, field convertible duct connections for down
discharge supply/return or horizontal discharge supply/return.
Cooling units, designed for outdoor mounted installation. ACP
units shall have minimum SEER ratings of 13. They shall have
built in, equal size, field convertible duct connections for down
discharge supply/return or horizontal discharge supply/return.
The units shall be factory wired, piped, charged with R-22
refrigerant and factory tested prior to shipment. All unit wiring
shall be both numbered and color coded.
refrigerant and factory tested prior to shipment. All unit wiring
shall be both numbered and color coded.
All units shall be manufactured in a facility certified to ISO 9001
standards, and the cooling performance shall be rated in
accordance with DOE and ARI test procedures. Units shall be
certified to UL 1995/CAN/CSA C22.2 No. 236 standard.
standards, and the cooling performance shall be rated in
accordance with DOE and ARI test procedures. Units shall be
certified to UL 1995/CAN/CSA C22.2 No. 236 standard.
UNIT CABINET
1.
Unit cabinet shall be constructed of galvanized steel, with
exterior surfaces coated with a non-chalking, powered
paint finish, certified at 1000 hours salt spray test per
ASTM-B117 standards.
exterior surfaces coated with a non-chalking, powered
paint finish, certified at 1000 hours salt spray test per
ASTM-B117 standards.
2.
The unit top shall be a single piece “Water Shed” design,
with drip edges and no-seam corners to provide optimum
water integrity.
with drip edges and no-seam corners to provide optimum
water integrity.
3.
Unit shall have a rigidly mounted condenser coil guard to
provide protection from objects and personnel after
installation.
provide protection from objects and personnel after
installation.
4.
Indoor blower section shall be insulated with up to 3/4”
thick, aluminum, foil faced insulation, fastened to prevent
insulation from entering the air stream.
thick, aluminum, foil faced insulation, fastened to prevent
insulation from entering the air stream.
5.
Cabinet panels shall be “large” size, easily removable for
servicing and maintenance, with built-in lift handles.
servicing and maintenance, with built-in lift handles.
6.
Unit shall be built on a formed, “Super-Structure” design
base pan, with embossments at critical points to add
strength, rigidity and aid in minimizing sound.
base pan, with embossments at critical points to add
strength, rigidity and aid in minimizing sound.
7.
Full perimeter base rails shall be provided to assure
reliable transit of equipment, overhead rigging, fork truck
access and proper sealing on roof curb applications. Base
rails shall be removable, when required, to lower unit
height.
reliable transit of equipment, overhead rigging, fork truck
access and proper sealing on roof curb applications. Base
rails shall be removable, when required, to lower unit
height.
8.
Filters shall be furnished and be accessible through a
removable access door, sealed air tight. (Single phase
models - accessory kit available. Three phase models -
standard from factory.)
removable access door, sealed air tight. (Single phase
models - accessory kit available. Three phase models -
standard from factory.)
9.
Units vertical discharge and return duct configuration shall
be designed to fit between standard 24” O.C. beams
without modification to building structure, duct work and
base unit.
be designed to fit between standard 24” O.C. beams
without modification to building structure, duct work and
base unit.
10. Condensate pan shall be internally sloped and conform to
ASHARE 62-89 self-draining standards, with ¾” NPTI
copper, ridged mount connection.
copper, ridged mount connection.
INDOOR (EVAPORATOR) FAN ASSEMBLY
1.
The ACP fan motor shall be direct drive, 5 speed design.
2.
Fan wheel shall be double-inlet type with forward-curved
blades, dynamically balanced to operate smoothly
throughout the entire range of operation. Airflow design
shall be constant air volume.
blades, dynamically balanced to operate smoothly
throughout the entire range of operation. Airflow design
shall be constant air volume.
3.
Bearings shall be sealed and permanently lubricated for
longer life and no maintenance.
longer life and no maintenance.
4.
Fan assembly shall be “Slip Track” (slide-out) design for
easy removal and cleaning.
easy removal and cleaning.
OUTDOOR (CONDENSER) FAN ASSEMBLY
1.
The outdoor fan shall be of the direct-driven propeller type,
discharge air vertically, have aluminum blades riveted to
corrosion resistant steel spider bracket and shall be
statically balanced for smooth operation.
discharge air vertically, have aluminum blades riveted to
corrosion resistant steel spider bracket and shall be
statically balanced for smooth operation.
2.
The outdoor fan motor shall be totally enclosed with
permanently lubricated bearings and internally protected
against overload conditions.
permanently lubricated bearings and internally protected
against overload conditions.
REFRIGERANT COMPONENTS
1.
Compressors:
a. Shall be fully hermetic reciprocating type, direct drive,
internally protected with internal high-pressure relief and
over temperature protection. The hermetic motor shall be
suction gas cooled and have a voltage range of + or -
10% of the unit nameplate voltage.
over temperature protection. The hermetic motor shall be
suction gas cooled and have a voltage range of + or -
10% of the unit nameplate voltage.
b Shall have internal isolation and sound muffling to
minimize vibration and noise, and be externally isolated
on a dedicated, independent mounting.
on a dedicated, independent mounting.
2.
Coils:
a. Evaporator and condenser coils shall have aluminum
plate fins mechanically bonded to seamless internally-
enhanced copper tubes with all joints brazed.
enhanced copper tubes with all joints brazed.
b Evaporator and Condenser coils shall be of the direct
expansion, draw-thru design.
3.
Refrigerant Circuit and Refrigerant Safety Components
shall include:
shall include:
a. Independent fixed-orifice or balanced port bi-flow TXV
expansion devices.
b. Filter/strainer to eliminate any foreign matter.
c. Accessible service gage connections on both suction
and discharge lines to charge, evacuate, and measure
refrigerant pressure during any necessary servicing or
troubleshooting, without losing charge and without
disrupting condenser or evaporator air flow.
refrigerant pressure during any necessary servicing or
troubleshooting, without losing charge and without
disrupting condenser or evaporator air flow.
d The refrigeration system shall provide at least 10° F of
liquid sub-cooling at design conditions.
4.
Unit Controls: