Monessen Hearth CSDV40SLP Manuel D’Utilisation
26
58D6056
CSDV Series Direct Vent Gas Stove
LOG pLACEmENT
Before you begin — This unit is supplied with ceramic fiber logs. Do not handle these logs
with your bare hands. Always wear gloves to prevent skin irritation from ceramic fibers.
After handling the logs, wash your hands gently with soap and water to remove any traces of
fibers.
with your bare hands. Always wear gloves to prevent skin irritation from ceramic fibers.
After handling the logs, wash your hands gently with soap and water to remove any traces of
fibers.
W
ARNING
The positioning of the logs is critical to the safe and clean operation of
this heater. Sooting and other problems may result if the logs are not
properly and firmly positioned in the appliance. Never add additional logs
or embellishments such as pine cones or vermiculite to the heater. Only
use the logs supplied with the unit.
Failure to position the parts in accordance with diagrams below or to use
only parts specifically approved for this heater may result in property
damage or personal injury.
this heater. Sooting and other problems may result if the logs are not
properly and firmly positioned in the appliance. Never add additional logs
or embellishments such as pine cones or vermiculite to the heater. Only
use the logs supplied with the unit.
Failure to position the parts in accordance with diagrams below or to use
only parts specifically approved for this heater may result in property
damage or personal injury.
pLACE CSDV20 LOGS IN FIREBOx
Figure 36
1. Carefully remove logs from wrapping.
2. Open front door of firebox.
3. Place rear log (#1) on rear log pin.
4. Place left base log (#2) on the two pins against left
1. Carefully remove logs from wrapping.
2. Open front door of firebox.
3. Place rear log (#1) on rear log pin.
4. Place left base log (#2) on the two pins against left
side of firebox.
5. Place right base log (#3) on the two pins against right
side of firebox.
PIL
OT
OFF
REMO
TE C
ONTR
OL
LG813
CSDV20 logs
CSDV20 logs
Left Base
Log #2
Log #2
Right Base
Log #3
Log #3
Rear Log
#1
#1
Pins
Pins
LG813
Figure 36 -
Place CSDV20 Logs
on Base
Place CSDV20 Logs
on Base
pLACE ROCK WOOL (EmBER mATERIAL)
IN FIREBOx
IN FIREBOx
Break up rock wool (ember material) into dime-sized
pieces. Fluff up rock wool. Place rock wool evenly across
burner surface. Do not block any areas around the perim-
eter of the burner, as these are the areas that supply the
needed air for secondary combustion. Do not place rock
wool under logs. Figure 37
NOTE: Do not exceed one (1) layer of rock wool
overage. place a small amount of rock wool on the
rear side of the burner only between tabs. The tabs are
designed to indicate the area where rock wool location.
Do not place rock wool outside the tabs in the back.
pieces. Fluff up rock wool. Place rock wool evenly across
burner surface. Do not block any areas around the perim-
eter of the burner, as these are the areas that supply the
needed air for secondary combustion. Do not place rock
wool under logs. Figure 37
NOTE: Do not exceed one (1) layer of rock wool
overage. place a small amount of rock wool on the
rear side of the burner only between tabs. The tabs are
designed to indicate the area where rock wool location.
Do not place rock wool outside the tabs in the back.
PIL
OT
OFF
REMO
TE C
ONTR
OL
LG814
CSDV20 rockwool
CSDV20 rockwool
Rock Wool
LG814
Figure 37 -
CSDV20 Rock Wool Placement
CSDV20 Rock Wool Placement