Lightolier 26556MPC Fascicule
READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALLING FIXTURE
This fixture is intended for installation in accordance with the National Electrical Code and local regulations.
To assure full compliance with local codes and regulations, check with your local electrical inspector before
installation. To prevent electrical shock, turn off electricity at fuse box before proceeding.
To assure full compliance with local codes and regulations, check with your local electrical inspector before
installation. To prevent electrical shock, turn off electricity at fuse box before proceeding.
Retain these instructions for maintenance reference.
INSTRUCTION SHEET NO.
I S :2 6 5 5 6 M P C
0798
Page 1 of 2
INSTALLATION INSTRUCTIONS FOR ATTACHING AND OPERATING
ProSpec
™
TRACK LIGHTING FIXTURE. FOR PIPE CLAMP MOUNT.
LIGHTOLIER a GENLYTE company.
631 Airport Road, Fall River, MA 02720
631 Airport Road, Fall River, MA 02720
Pipe clamp will fit on the following Pipes:
Round pipe from 3/4” to 1 1/2” nominal pipe size.
NOTE: 3/4” pipe has an actual outside diameter of 1.05”.
1 1/2” nominal pipe has actual outside diameter of 1.90”
NOTE: 3/4” pipe has an actual outside diameter of 1.05”.
1 1/2” nominal pipe has actual outside diameter of 1.90”
1. Loosen CLAMP SCREW enough to allow pipe to fit in
CLAMP.
2. Hang FIXTURE on pipe.
3. Tighten CLAMP SCREW to pipe.
4. Wrap SAFETY CABLE around pipe. Bend “S” HOOK closed
4. Wrap SAFETY CABLE around pipe. Bend “S” HOOK closed
around CABLE.
NOTE: The proper LAMP should be installed into the
FIXTURE prior to energizing. See instructions below.
NOTE: The proper LAMP should be installed into the
FIXTURE prior to energizing. See instructions below.
INSTRUCTIONS FOR ATTACHING FIXTURE TO A
PIPE (Fig. 1)
PIPE (Fig. 1)
CAUTION:
• Turn off power at fuse box before plugging fixture into outlet.
• Fixture temperature is extremely high during operation. Use heat resident gloves or other heat resistant materials to pro-
• Fixture temperature is extremely high during operation. Use heat resident gloves or other heat resistant materials to pro-
tect hands when adjusting or handling the fixture during operation.
• Do not install fixture near combustible materials.
• Fixture is not for residential use.
• Fixture is not for residential use.
The following lamps may be used in the FIXTURE:
Fixture Cat. No. 26556M, WHPC, BKPC
Lamp
Lamp
12 Volt PAR 56 Screw Terminal
120 to 240 Watt
120 to 240 Watt
1. Holding SNOOT loosen ACCESS KNOB a few turns until
SNOOT opens.
2. Screw SPADE TERMINALS into LAMP TERMINALS.
3. Align 3 LAMP BOSSES with 3 RING NOTCHES. Align
3. Align 3 LAMP BOSSES with 3 RING NOTCHES. Align
LAMP SCREW TERMINALS with LAMP ALIGNMENT
BRACKET. Push LAMP into FIXTURE until LAMP SPRINGS
hold LAMP.
NOTE: The 3 LAMP BOSSES must sit in the 3 RING
NOTCHES after the LAMP is installed.
BRACKET. Push LAMP into FIXTURE until LAMP SPRINGS
hold LAMP.
NOTE: The 3 LAMP BOSSES must sit in the 3 RING
NOTCHES after the LAMP is installed.
4. Removing LAMP: Snap LAMP out of LAMP SPRINGS.
Unscrew LAMP TERMINALS.
LAMPING & USING ACCESSORIES (Fig. 1)
LAMP BOSS
SNOOT
ACCESS KNOB
LAMP ALIGNMENT
BRACKET
BRACKET
LAMP SPRING
PIPE
SPADE TERMINAL
RING NOTCH
LAMP TERMINAL
SWITCH
CLAMP SCREW
SAFETY CABLE
“S” HOOK
MALE PLUG
Fig. 1