Lightolier IS:404SK Fascicule
READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALLING LUMINAIRE
This luminaire is intended for installation in accordance with the National Electrical Code and local regulations.
To assure full compliance with local codes and regulations, check with your local electrical inspector before
installation. To prevent electric shock, turn off electricity at fuse box before proceeding.
Retain these instructions for maintenance reference.
IS:404SK
INSTRUCTION SHEET NO.
A0204
Page 1
631 Airport Road, Fall River, MA 02720
COMPANY
A
INSTRUCTION SHEET FOR ASSEMBLY AND INSTALLATION OF
9”,12”&16” PENDALYTE™ SERIES WITH CORD AND CABLE
Note: This instruction sheet covers several luminaire styles.
Powerhead assembly, lamp type, and reflector style may vary slightly
from that shown, although installation is the same.
Powerhead assembly, lamp type, and reflector style may vary slightly
from that shown, although installation is the same.
CANOPY INSTALLATION (fig. 1):
1.
1.
Thread 1/4-20 SCREW through CROSSBAR as shown.
2.
Using appropriate slots in CROSSBAR, secure CROSSBAR to
outlet box using OUTLET BOX SCREWS (provided with outlet
box).
outlet box using OUTLET BOX SCREWS (provided with outlet
box).
3.
Make electrical connections: black POWERCORD lead to hot
(black) supply lead; white POWERCORD lead to neutral (white)
supply lead. Green POWERCORD lead is ground wire and must
be connected to grounding terminal or ground lead inside outlet
box. Use WIRE NUTS (local hardware item). Push supply leads
into outlet box. Note: Refer to POWERHEAD instruction sheet
for detailed wiring information.
(black) supply lead; white POWERCORD lead to neutral (white)
supply lead. Green POWERCORD lead is ground wire and must
be connected to grounding terminal or ground lead inside outlet
box. Use WIRE NUTS (local hardware item). Push supply leads
into outlet box. Note: Refer to POWERHEAD instruction sheet
for detailed wiring information.
4.
Secure POWERCORD into CANOPY with RELIEF BUSHING.
5.
Slide CABLE through CABLE COUPLER as shown.
6.
Attach CANOPY by placing over 1/4-20 SCREW and securing
with CABLE COUPLER.
with CABLE COUPLER.
CAUTION: MAKE CERTAIN WIRES ARE NOT PINCHED
BETWEEN PARTS.
BETWEEN PARTS.
POWERHEAD INSTALLATION (fig. 2):
1.
1.
Attach CABLE ADJUSTER to MOUNT PLATE with PANEL NUT.
Note: On 9” unit MOUNT PLATE must be oriented correctly
to clear DOOR SCREW head (see fig. 2).
Note: On 9” unit MOUNT PLATE must be oriented correctly
to clear DOOR SCREW head (see fig. 2).
2.
Pass POWERCORD through relief bushing hole in MOUNT
PLATE.
PLATE.
3.
While supporting POWERHEAD ASSEMBLY wire luminaire using
WIRE NUTS (local hardware item): black luminaire lead to hot
(black) POWERCORD lead, white luminaire lead to neutral
(white) POWERCORD lead. Attach luminaire ground wire(s)
(green and/or bare) to green ground wire from POWERCORD.
WIRE NUTS (local hardware item): black luminaire lead to hot
(black) POWERCORD lead, white luminaire lead to neutral
(white) POWERCORD lead. Attach luminaire ground wire(s)
(green and/or bare) to green ground wire from POWERCORD.
4.
Height adjustment: to raise luminaire push excess POWERCORD
down into POWERHEAD. (Make certain CABLE does not
interfere with internal wiring or components, both POWERCORD
and CABLE may be cut inside POWERHEAD. Remove DOOR
SCREW and pull DOOR away from POWERHEAD). CABLE is
inserted into CABLE ADJUSTER. Raise luminaire by providing
slack in CABLE and pushing through CABLE ADJUSTER. Lower
luminaire by depressing PLUNGER .
down into POWERHEAD. (Make certain CABLE does not
interfere with internal wiring or components, both POWERCORD
and CABLE may be cut inside POWERHEAD. Remove DOOR
SCREW and pull DOOR away from POWERHEAD). CABLE is
inserted into CABLE ADJUSTER. Raise luminaire by providing
slack in CABLE and pushing through CABLE ADJUSTER. Lower
luminaire by depressing PLUNGER .
5.
Secure POWERCORD to MOUNT PLATE with STRAIN RELIEF.
6.
Attach MOUNT PLATE to POWERHEAD with 8-32 SCREWS.
Fig. 2
CROSSBAR
OUTLET BOX
SCREWS
CANOPY
RELIEF BUSHING
POWERCORD
RELIEF BUSHING
MOUNT PLATE
WIRE NUTS
POWERHEAD
ASSEMBLY
ASSEMBLY
CABLE COUPLER
CABLE ADJUSTER
8-32 SCREWS
PANEL NUT
PLUNGER
CABLE
1/4-20 SCREW
Fig. 1
SUPPLY
LEADS
DOOR
SCREW
CAUTION: MAXIMUM WATTAGE AS MARKED ON
LUMINAIRE MUST NOT BE EXCEEDED.
LUMINAIRE MUST NOT BE EXCEEDED.
DOOR