Lightolier IS:4A28442 Fascicule
READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALLING LUMINAIRE
This luminaire is intended for installation in accordance with the National Electrical Code and local regulations. To
assure full compliance with local codes and regulations, check with your local electrical inspector before
installation. To prevent electric shock, turn off electricity at fuse box before proceeding.
Retain these instructions for maintenance reference.
INSTRUCTIONS FOR INSTALLATION OF PENDALUX
PENDANT SERIES
INSTRUCTION SHEET NO.
IS:4A28442
A0501
Page 1 of 2
A
COMPANY
631 Airport Road, Fall River, MA 02720
INSTALLATION (Fig. 1):
1.
After opening carton and removing top packaging material,
allow CHASSIS to remain in carton for protection.
allow CHASSIS to remain in carton for protection.
2.
Assemble SUSPENSION system following the appropriate
instructions outlined below.
instructions outlined below.
Suspension Assembly:
Single Stem Suspensions (4SB1 Series):
Single Stem Suspensions (4SB1 Series):
1.
If no extension kit is to be used; cut three wires (BLACK,
WHITE and GREEN) no less than 6” above SWIVEL BALL.
Strip back insulation from each wire approximately 3/8” from
each end (Fig. 1).
WHITE and GREEN) no less than 6” above SWIVEL BALL.
Strip back insulation from each wire approximately 3/8” from
each end (Fig. 1).
2.
If an extension kit is to be used, follow instructions provided
with extension kit.
with extension kit.
Multi-Stem, Contemporary and Traditional 3-Arm
Suspensions (4SB2, 4SB3 & 4SB4 Series):
Suspensions (4SB2, 4SB3 & 4SB4 Series):
1.
If no extension kit is to be used; cut three wires (BLACK,
WHITE and GREEN) no less than 6” above SWIVEL BALL.
Strip back insulation from each wire approximately 3/8” from
each end (Fig. 1).
WHITE and GREEN) no less than 6” above SWIVEL BALL.
Strip back insulation from each wire approximately 3/8” from
each end (Fig. 1).
2.
If extension kit is not to be used, thread UPPER STEM into
THREAD ADAPTOR until tight (Fig. 1).
THREAD ADAPTOR until tight (Fig. 1).
3.
Using ALLEN WRENCH provided tighten two SET SCREWS
in the sides of THREADED ADAPTOR securing UPPER
STEM in position.
in the sides of THREADED ADAPTOR securing UPPER
STEM in position.
4.
Cut three wires (BLACK, WHITE and GREEN) no less than 6”
above SWIVEL BALL. Strip back insulation from each wire
approximately 3/8” from each end (Fig. 1).
above SWIVEL BALL. Strip back insulation from each wire
approximately 3/8” from each end (Fig. 1).
5.
If an extension kit is to be used, follow instructions provided
with extension kit.
NOTE: For the Traditional 3-Arm suspensions, the upper half
of COLLECTOR BALL can be pulled upward to gain access
to THREADED ADAPTOR (Fig. 8).
with extension kit.
NOTE: For the Traditional 3-Arm suspensions, the upper half
of COLLECTOR BALL can be pulled upward to gain access
to THREADED ADAPTOR (Fig. 8).
Suspension Installation:
1.
Position SUSPENSION next to CHASSIS and insert MALE
CONNECTOR from SUSPENSION into FEMALE
CONNECTOR and snap together.
CONNECTOR from SUSPENSION into FEMALE
CONNECTOR and snap together.
2.
Pass RED WIRE from CHASSIS up through CENTER PIPE
on SUSPENSION.
on SUSPENSION.
3.
If necessary, cut and strip back insulation on RED WIRE as
done in step one under suspension assembly above.
done in step one under suspension assembly above.
4.
Loosen three SCREWS on the top of CHASSIS as shown in
fig. 1.
fig. 1.
5.
Position KEYSLOTS in SUSPENSION PLATE over three
SCREWS on top of CHASSIS (Fig. 1).
SCREWS on top of CHASSIS (Fig. 1).
6.
Twist SUSPENSION PLATE clockwise allowing three
SCREW HEADS to pass over BUMPS on the sides of
KEYSLOTS.
SCREW HEADS to pass over BUMPS on the sides of
KEYSLOTS.
7.
Secure SUSPENSION in place by fully tightening three
SCREWS.
SCREWS.
CAUTION: USE LAMP WATTAGE AND TYPE AS
MARKED ON LUMINAIRE
MARKED ON LUMINAIRE
Note: This instruction sheet covers several luminaire (fixture) styles. Although suspension, chassis, lamp type and diffuser may vary from that shown,
installation is the same.
installation is the same.
SCREW
SWIVEL BALL
RED WIRE
WHITE WIRES
GREEN WIRES
BLACK WIRES
RED WIRE
FEMALE
CONNECTOR
CHASSIS
MALE CONNECTOR
SUSPENSION
SUSPENSION PLATE
SCREWHEAD
KEYSLOT
BUMP
FIG. 3
FIG. 1
FIG. 2